Roland JUNO-D - Manual (Page 69)

69
Adding effects
Effects
Send Lvl to Cho
(Multi-effect send level to chorus)
Sets the amount of the multi-effects sound that is sent to the chorus.
Higher values result in more sound being sent.
Value: 0–127
Send Lvl to Rev
(Multi-effect send level to reverb)
Sets the amount of the multi-effects sound that is sent to the reverb.
Higher values result in more sound being sent.
Value: 0–127
Ctrl 1, 2 (Multi-Effects Control 1, 2)
On the JUNO-D, certain multi-effect parameters can be assigned to
the modulation lever, knobs, pedal or D Beam. Of the parameters
explained in
Multi-effect parameters , the assignable parameters are
marked with a “#” symbol. (Parameters marked with “#1” or “#2”
can be simultaneously controlled using the controller marked with
the same number.) Here you can exchange these assignments, or
choose not to use them. For details, refer to p. 33, p. 89.
Value
OFF: Multi-effect control will not be used.
Items with a “#” symbol: The parameters that can be assigned to
Ctrl1 or Ctrl2. These differ depending on the multi-effect
type.
00: THROUGH
Effects are not applied. Select when creating Patches or Rhythm Sets
that do not use multi-effects.
01: STEREO EQ (Stereo Equalizer)
This is a four-band stereo equalizer (low, mid x 2, high).
fig.MFX-01
02: OVERDRIVE
This effect creates a soft distortion similar to that produced by
vacuum tube amplifiers.
fig.MFX-02
Parameter Value Description
Low Freq 200, 400 [Hz] Selects the frequency of the low
range.
Low Gain -15– +15 [dB] Adjusts the gain of the low fre-
quency.
High Freq 2000, 4000, 8000
[Hz] Selects the frequency of the high
range.
High Gain -15– +15 [dB] Adjusts the gain of the high fre-
quency.
Mid1 Freq 200–8000 [Hz] Adjusts the frequency of Middle
1 (mid range).
Mid1 Q 0.5, 1.0, 2.0, 4.0,
8.0 This parameter adjusts the
width of the area around the
Middle 1 Frequency that will be
affected by the Gain setting.
Higher values of Q will result in
a narrower area being affected.
L in
R in
L out
R out
4-Band EQ
4-Band EQ
Mid1 Gain -15– +15 [dB] Adjusts the gain for the area
specified by the Middle 1 Fre-
quency and Q settings.
Mid2 Freq 200–8000 [Hz] Adjusts the frequency of Middle
2 (mid range).
Mid2 Q 0.5, 1.0, 2.0, 4.0,
8.0 This parameter adjusts the
width of the area around the
Middle 2 Frequency that will be
affected by the Gain setting.
Higher values of Q will result in
a narrower area being affected.
Mid2 Gain -15– +15 [dB] Adjusts the gain for the area
specified by the Middle 2 Fre-
quency and Q settings.
Level # 0–127 Adjusts the output level.
Parameter Value Description
Drive # 0–127 Adjusts the degree of distortion.
The volume will change togeth-
er with the degree of distortion.
Pan # L64–63R Adjusts the stereo location of the
output sound.
L64 is far left, 0 is center, and
63R is far right.
Amp Type SMALL,
BUILT-IN,
2-STACK,
3-STACK Selects the type of guitar amp.
SMALL: small amp
BUILT-IN: single-unit type amp
2-STACK: single-unit type amp
3-STACK: large triple stack amp
Low Gain -15– +15 [dB] Adjusts the gain of the low fre-
quency.
High Gain -15– +15 [dB] Adjusts the gain of the high fre-
quency.
Level 0–127 Adjusts the output level.
Parameter Value Description
Amp
Simulator
2-Band
EQ
L in
R in
Over
drive
L out
R out
Pan R
Pan L
JUNO-D_e.book 69 ページ ２００４年６月１１日 金曜日 午後１時２１分