Roland JUNO-D - Manual (Page 79)

79
Adding effects
Effects
26: GATED REVERB
Gate Reverb is a special type of reverb in which the reverberant
sound is cut off before its natural length.
fig.MFX-26
27: OD>CHORUS
(Overdrive
→
Chorus)
This effect connects an overdrive and a chorus in series.
fig.MFX-27
28: OD>FLANGER
(Overdrive
→ Flanger)
This effect connects an overdrive and a flanger in series.
fig.MFX-28
Parameter Value Description
Type NORMAL,
REVERSE,
SWEEP1,
SWEEP2 Selects the type of reverb.
NORMAL: conventional gate re-
verb
REVERSE: backwards reverb
SWEEP1: the reverberant sound
moves from right to left
SWEEP2: the reverberant sound
moves from left to right
Pre Delay 0.0–100 [ms] Adjusts the time delay from
when the direct sound begins
until the reverb sound is heard.
Gate Time 5–500 [ms] Adjusts the time from when the
reverb is heard until when it dis-
appears.
Low Gain -15– +15 [dB] Adjusts the gain of the low fre-
quency.
High Gain -15– +15 [dB] Adjusts the gain of the high fre-
quency.
Balance # D100:0W–
D0:100W Adjusts the volume balance be-
tween the direct sound and the
reverb sound.
With a setting of D100:0W only the
direct sound will be output, and
with a setting of D0:100W only the
reverb sound will be output.
Level # 0–127 Adjusts the output level.
Parameter Value Description
OD Drive 0–127 Adjusts the degree of overdrive
distortion.
The volume will change togeth-
er with the degree of distortion.
OD Pan # L64–63R Adjusts the stereo location of the
overdrive sound.
L64 is far left, 0 is center, and
63R is far right.
L in
R in
L out
R out
Gated Reverb
2-Band
EQ
Balance W
Balance W
Balance D
Balance D
2-Band
EQ
L in
R in
Chorus Overdrive
L out
R out
Balance W
Balance W
Balance D
Balance D
Cho Delay 0.0–100 [ms] Adjusts the time delay from
when the direct sound begins
until the chorus sound is heard.
Cho Rate 0.05–10.00 [Hz] Adjusts the modulation speed of
the chorus effect.
Cho Depth 0–127 Adjusts the modulation depth of
the chorus effect.
Cho Balance # D100:0W–
D0:100W Adjusts the volume balance be-
tween the overdrive sound that
is sent through the chorus and
the overdrive sound that is not
sent through the chorus.
With a setting of “D100:0W,”
only the overdrive sound will be
output. With a setting of
“D0:100W,” only the overdrive
sound that is sent through the
chorus will be output.
Level 0–127 Adjusts the output level.
Parameter Value Description
OD Drive 0–127 Adjusts the degree of overdrive
distortion.
The volume will change togeth-
er with the degree of distortion.
OD Pan # L64–63R Adjusts the stereo location of the
overdrive sound.
L64 is far left, 0 is center, and
63R is far right.
Flg Delay 0.0–100 [ms] Adjusts the time delay from
when the direct sound begins
until the flanger sound is heard.
Flg Rate 0.05–10.00 [Hz] Adjusts the modulation speed of
the flanger effect.
Flg Depth 0–127 Adjusts the modulation depth of
the flanger effect.
Flg Feedback -98– +98 [%] Adjusts the proportion (%) of
the flanger sound that is fed
back into the effect.
Negative (-) settings will invert
the phase.
Parameter Value Description
L in
R in
Flanger Overdrive
L out
R out
Balance W
Balance W
Balance D
Balance D
Feedback
JUNO-D_e.book 79 ページ ２００４年６月１１日 金曜日 午後１時２１分