National Instruments AT E Series User Manual
At e series user manual
Table of contents
Document Outline
- AT E Series User Manual
- Support
- Important Information
- Compliance
- Contents
- About This Manual
- Chapter 1 Introduction
- Chapter 2 Installing and Configuring the Device
- Chapter 3 Hardware Overview
- Figure 3-1. AT-MIO-16E-1 and AT-MIO-16E-2 Block Diagram
- Figure 3-2. AT-MIO-64E-3 Block Diagram
- Figure 3-3. AT-MIO-16E-10 and AT-MIO-16DE-10 Block Diagram
- Figure 3-4. AT-MIO-16XE-10 Block Diagram
- Figure 3-5. AT-AI-16XE-10 Block Diagram
- Figure 3-6. AT-MIO-16XE-50 Block Diagram
- Analog Input
- Analog Output
- Analog Trigger
- Digital I/O
- Timing Signal Routing
- Chapter 4 Connecting Signals
- Table 4-1. I/O Connector Details
- I/O Connector
- Figure 4-1. I/O Connector Pin Assignment for the AT-MIO-16E-1, AT-MIO-16E-2, AT-MIO-16E-10...
- Figure 4-2. I/O Connector Pin Assignment for the AT-MIO-64E-3
- Figure 4-3. I/O Connector Pin Assignment for the AT-MIO-16DE-10
- I/O Connector Signal Descriptions
- Table 4-2. I/O Signal Summary for the AT E Series
- Table 4-3. I/O Signal Summary for the AT-MIO-16E-1, AT-MIO-16E-2, and AT-MIO-64E-3
- Table 4-4. I/O Signal Summary for the AT-MIO-16E-10 and AT-MIO-16DE-10
- Table 4-5. I/O Signal Summary for the AT-MIO-16XE-10 and AT-AI-16XE-10
- Table 4-6. I/O Signal Summary for the AT-MIO-16XE-50
- Analog Input Signal Connections
- Types of Signal Sources
- Input Configurations
- Analog Output Signal Connections
- Digital I/O Signal Connections
- Power Connections
- Timing Connections
- Figure 4-12. TIO Connections
- Programmable Function Input Connections
- DAQ Timing Connections
- Figure 4-13. Typical Posttriggered Acquisition
- Figure 4-14. Typical Pretriggered Acquisition
- TRIG1 Signal
- Figure 4-15. TRIG1 Input Signal Timing
- Figure 4-16. TRIG1 Output Signal Timing
- TRIG2 Signal
- Figure 4-17. TRIG2 Input Signal Timing
- Figure 4-18. TRIG2 Output Signal Timing
- STARTSCAN Signal
- Figure 4-19. STARTSCAN Input Signal Timing
- Figure 4-20. STARTSCAN Output Signal Timing
- CONVERT* Signal
- Figure 4-21. CONVERT* Input Signal Timing
- Figure 4-22. CONVERT* Output Signal Timing
- AIGATE Signal
- SISOURCE Signal
- Figure 4-23. SISOURCE Signal Timing
- SCANCLK Signal
- Figure 4-24. SCANCLK Signal Timing
- EXTSTROBE* Signal
- Figure 4-25. EXTSTROBE* Signal Timing
- Waveform Generation Timing Connections
- General-Purpose Timing Signal Connections
- GPCTR0_SOURCE Signal
- Figure 4-31. GPCTR0_SOURCE Signal Timing
- GPCTR0_GATE Signal
- Figure 4-32. GPCTR0_GATE Signal Timing in Edge-Detection Mode
- GPCTR0_OUT Signal
- Figure 4-33. GPCTR0_OUT Signal Timing
- GPCTR0_UP_DOWN Signal
- GPCTR1_SOURCE Signal
- Figure 4-34. GPCTR1_SOURCE Signal Timing
- GPCTR1_GATE Signal
- Figure 4-35. GPCTR1_GATE Signal Timing in Edge-Detection Mode
- GPCTR1_OUT Signal
- Figure 4-36. GPCTR1_OUT Signal Timing
- GPCTR1_UP_DOWN Signal
- Figure 4-37. GPCTR Timing Summary
- FREQ_OUT Signal
- Timing Specifications for Digital I/O Ports A, B, and C
- Field Wiring Considerations
- Chapter 5 Calibrating the Device
- Appendix A Specifications
- Appendix B Optional Cable Connector Descriptions
- Figure B-1. 68-Pin MIO Connector Pin Assignments
- Figure B-2. 68-Pin DIO Connector Pin Assignments
- Figure B-3. 68-Pin Extended AI Connector Pin Assignments
- Figure B-4. 50-Pin MIO Connector Pin Assignments
- Figure B-5. 50-Pin DIO Connector Pin Assignments
- Figure B-6. 50-Pin Extended AI Connector Pin Assignments
- Appendix C Common Questions
- Appendix D Technical Support and Professional Services
- Glossary
- Index