Philips DIGA DMR-BW750 - Manual (Page 45)

45
RQT9428
Pla
ying
bac
k
To enjoy High Bit rate Audio and Video
Enjoying High Bit rate Audio with 7.1ch speaker
This unit can decode high bit rate audio (Dolby Digital Plus, Dolby TrueHD, DTS-HD High Resolution Audio and DTS-HD Master Audio) adopted
in BD-Video.
To enjoy 7.1ch surround sound, the following conditions are necessary (Part shown in the shaded area of table given below).
Connect an amplifi er/receiver with 7.1ch speaker supporting HDMI (High Bit rate Audio) using a High Speed HDMI cable. ( ➡ 100)
Set “BD-Video Secondary Audio” to “Off” in the Setup menu. ( ➡ 91)
Set “Dolby D/Dolby D +/Dolby TrueHD” or “DTS/DTS-HD” to “Bitstream” or “PCM” in the Setup menu. ( ➡ 91)
About audio from audio output terminal
Connect an amplifi er/receiver and confi rm the desired audio type and necessary settings (“BD-Video Secondary Audio”, “Dolby D/Dolby D +/
Dolby TrueHD” or “DTS/DTS-HD”).
The number of channels listed is the maximum possible number of output channels.
Also, depending on the specifi cations or the settings of the amplifi er/receiver, the results of the output may vary.
Terminal HDMI AV OUT DIGITAL AUDIO OUT
“Dolby D/Dolby D +/
Dolby TrueHD”/
“DTS/DTS-HD”
“Bitstream” 1 “PCM” 3 “Bitstream” “PCM”
“BD-Video
Secondary Audio”
“On” 2 “Off” “On” “Off” “On”/“Off” “On”/“Off”
Dolby Digital/
Dolby Digital EX 5
Dolby Digital/
Dolby Digital
EX 6
Dolby Digital/
Dolby Digital EX
5.1ch PCM
Dolby Digital/
Dolby Digital
EX 6
Down-mixed 2ch
PCM
Dolby Digital Plus
Dolby Digital
Dolby Digital Plus
5.1ch PCM 2 7.1ch PCM Dolby Digital
Dolby TrueHD Dolby TrueHD
DTS Digital
Surround/
DTS-ES 5
DTS Digital
Surround/DTS-
ES 6
DTS Digital
Surround/
DTS-ES
DVD-V 5.1ch PCM DTS Digital
Surround/
DTS-ES 6
BD-V 7.1ch PCM 4
DTS-HD High
Resolution Audio DTS Digital
Surround
DTS-HD High
Resolution Audio
7.1ch PCM 4
DTS Digital
Surround DTS-HD Master
Audio
DTS-HD Master
Audio
7.1ch LPCM
Down-mixed
5.1ch PCM
7.1ch PCM
Down-mixed
5.1ch PCM 2
7.1ch PCM
Down-mixed 2ch
PCM
1 When the connected equipment is not supported with these audio format, the audio is output as Dolby Digital bitstream, DTS Digital Surround
bitstream or down-mixed 2ch PCM (e.g., TV).
2 BD-V : When playing BD-Video without secondary audio or clicking sound, the audio is output as the same format as if “BD-Video Secondary
Audio” was set to “Off” in the Setup menu. ( ➡ 91)
3 When the connected equipment is not supported with multi channel surround, the audio is output as down-mixed 2ch PCM.
4 BD-V : When the connected equipment is supported with 7.1 channel surround, the audio output is amplifi ed from 5.1ch or 6.1ch to 7.1ch
depending on the DTS, Inc. specifi cations.
5 With PCM output, Dolby Digital EX becomes PCM audio decoded as Dolby Digital, DTS-ES recorded to DVD-Video becomes PCM audio
decoded as DTS Digital Surround, and DTS-ES recorded to BD-Video becomes PCM audio decoded as DTS-ES.
6 BD-V : When “BD-Video Secondary Audio” is set to “On” in the Setup menu, Dolby Digital EX is output as Dolby Digital and DTS-ES is output
as DTS Digital Surround, however if playing BD-Video without secondary audio or clicking sound, the audio is output as the original format.
Note
When setting “BD-Video Secondary Audio” to “Off” in the Setup menu, the clicking sound on the menu and audio with secondary video in
picture-in-picture mode ( ➡ 44) cannot be output.
Regarding 24p output
Many BD-Video movie contents are recorded in 24 frames/second in accordance with the fi lm materials. However, they will normally be output in
60 frames/second in accordance with the display format.
These can be output in 24p as the original. Therefore, high-quality video can be enjoyed, such as the improved clarity, enhanced perspective,
etc.
Preparation
Connect to a TV supporting 1080/24p input via an HDMI cable.
Set “BD-Video 24p Output” to “On” in the Setup menu. ( ➡ 92)
DMR-BW850GL_en.indb 45 DMR-BW850GL_en.indb 45 2009/04/08 午前 10:01:00 2009/04/08 午前 10:01:00