Panasonic PT VX400NTU - Manual (Page 60)

Setting
60
- ENGLISH
Settings
Attention
When selecting [Network], the cooling fans may be z
running depending on the temperature inside the
projector even if the projector is turned off.
If [Standby mode] is set to [Eco], the signals come z
from MONITOR OUT and AUDIO OUT terminal are
unavailable.
If [Standby mode] is set to [Eco], you can not use z
network functions when the projector is standing by. Also,
you cannot use some RS-232C protocol commands.
If set to [Network], you can use network functions z
when the projector is standing by. Refer to “Operating
Instructions - Network Operations ”.
P-timer
This function allows you to change the setting of the
P-timer and execute it.
Press ▲▼ to select [P-timer]. 1 )
Press ► or button to 2 ) access the submenu.Mode JPress ▲▼ button to select one mode 1 ) among the items as below.Count upThe P-timer display 000:00 appears on the screen and the count up starts (000:00-180:00)Count downThe time set in the Timer setting appears on the screen and the countdown starts.Timer JPress ▲▼ to select [Timer] and then 1 ) press the button.
Press▲▼ to set the [Timer](1-180 Min). 2 )
access the submenu.
Mode
J
Press ▲▼ button to select one mode 1 )
among the items as below.
Count up
The P-timer display 000:00
appears on the screen and the
count up starts (000:00-180:00)
Count down
The time set in the Timer setting
appears on the screen and the
countdown starts.
Timer
J
Press ▲▼ to select [Timer] and then 1 )
press the
2 )
Timer is available in [Count down] only. Factory z
default value is 10 Min.
Execute
J
Press ▲▼ to select one among the 1 )
items as below and then press the
button. StartIt executes the count up or count down function.*1ResetReset the P-timer values.*2ExitTo exit the P-timer operation.Press the button at [Start] and the
Start It executes the count up or count
down function.* 1
Reset Reset the P-timer values.* 2
Exit To exit the P-timer operation.
Press the *1 :
indication changes into [Stop]. To stop [Count up]
or [Count down], press the button at [Stop] on the screen menu, then the indication changes into [Restart]. Press the
[Stop] on the screen menu, then the indication
changes into [Restart]. Press the
button at [Restart] to resume [Count up] or [Count
down].
Press the button at [Reset] to return *2 : to the following value: Count up"000:00"Count down Timer that you setAttentionTo stop the [P-timer] function, press the zbutton.To cancel the [P-timer], press and hold the zbutton for a few seconds.Closed caption[Only for NTSC, 480i input]Press ▲▼ to select [Closed caption].1 ) Press ► or the button to *2 :
to the following value:
Count up "000:00"
Count down Timer that you set
Attention
To stop the [P-timer] function, press the z
button.
To cancel the [P-timer], press and hold the z
button for a few seconds.
Closed caption
[ Only for NTSC, 480i input]
Press ▲▼ to select [Closed caption]. 1 )
Press ► or the 2 )
enter the submenu.
Closed caption
J
Press ▲▼ to select [Closed caption] 1 )
and then press the button.
Press ▲▼ to select Off, CC1, CC2, 2 ) CC3 or CC4.Color JPress ▲▼ to select [Color] and then 1 ) press the button.
Press▲▼ to select color or white.
2 )
CC3 or CC4.
Color
J
Press ▲▼ to select [Color] and then 1 )
press the
2 )
Attention
The closed caption is mainly used in the north America. z
This function shows the text information contained in the
image signal. Captions may not be displayed on some
devices or software.
You can select [Closed caption] when [NTSC] or [480i] z
signals are input.
Part of characters may not displayed when high z
compensation valued are set in [Keystone].
Closed captions are not displayed while the menu screen z
appears.