Sharp AR-FX12 - Manual (Page 72)

STORING, EDITING, AND DELETING AUTO DIAL KEYS AND PROGRAMS
6-8
STORING A PROGRAM
You can store a destination fax number, speed dialing, polling, erase, dual page scan, 2in1, card shot, and resolution
and exposure settings in a program. This enables you to call up the program and perform the transmission by means
of a simplified operation. (See "USING A PROGRAM" on page 3-17.)
To store a program key, follow steps 1 through 3 on page 6-2, touch the [PROGRAM] key in step 4, and then follow these steps.
1 Touch the [PROGRAM NAME] key.
The "No." that
automatically appears is
the lowest number from 1 to
8 that has not yet been
programmed. When the
[PROGRAM NAME] key is
touched, the letter-entry
screen appears. Enter up to 18 characters for the name.
Refer to chapter 7 of "Operation manual (for general
information and copier operation)" for the procedure for
entering letters.
2 Touch the [SETTINGS] key.
3 Touch the keys for the settings you wish to
store.
For the detailed procedures for each of the settings, refer to
the explanations of those features on the following pages.
[RESOLUTION](page 1-10) [EXPOSURE](page 1-11)
[SPEED DIAL](page 2-4)
[ADDRESS BOOK] (page 3-3)
[SPECIAL MODES]
ERASE (page 3-4) DUAL PAGE SCAN (page 3-5)
2in1 (page 3-7) CARD SHOT (page 3-8)
POLLING (page 3-13)
4 Touch the [OK] key.
5 Your settings are displayed. Make sure
they are correct.
6 When you are finished, touch the [EXIT] key.
If you wish to store another program, touch
the [NEXT] key.
Touching the [EXIT] key returns you to the screen
of step 4 on page 6-2.
Touching the [NEXT] key returns you to the screen of step 1.
EDITING AND DELETING PROGRAMS
To edit or delete a previously stored program, follow steps 1 to 3 on page 6-2, touch the [AMEND/DELETE] key in
the screen of step 4, and then follow these steps.
1 Touch the [PROGRAM] key. 2 Touch the program you wish to edit or delete.
When you touch the program name, the edit/delete
screen for the selected program appears.
Touching the [ADDRESS BOOK] key returns you to
the screen of step 1.
3 To edit the program, follow the same procedure as
for storing the program. To delete the program,
touch the [DELETE] key and then touch the [YES]
key in the confirmation screen that appears.
NOTE
A timer setting (page 3-6) cannot be included in a program.
When storing a program for an F-Code operation, one touch keys for destinations must include sub-addresses.
PROGRAM
PROGRAM NAME
SETTINGS ADDRESS
RESOLUTION
No.1
PROGRAM NAME
SETTINGS ADDRESS
PROGRAM FOR SHARP
RESOLUTION
SPECIAL MODES
No.1
CANCEL OK
SPECIAL MODES
ADDRESS BOOK
ENTER PROGRAM YOU REQUIRE.
STANDARD
RESOLUTION
AUTO
EXPOSURE
ADDRESS REVIEW
MODE SWITCH
FAX
NOTE
Up to 500 (maximum of 300 on the AR-M351U/AR-
M451U) destinations can be stored in a program.
However, you cannot directly enter fax numbers with
the numeric keys. A destination must be programmed
in an auto dial key (one-touch key or group key) before
it can be stored in a program.
PROGRAM
SETTINGS
PROGRAM NAME
REGISTRATION
SHARP PROGRAM
ADDRESS
SPECIAL MODES
RESOLUTION
2 ADDRESSES
FINE AUTO EXPOSURE
DUAL PAGE SCAN
No.1
NEXT EXIT
EXIT
1/2
PROGRAM
DIRECT ADDRESS / AMEND/DELETE
PROGRAM
SELECT ADDRESS TO AMEND/DELETE.
EXIT
PROGRAM FOR SHARP EMAIL NEWS GROUP
ABYS FAX FORMAT A
ADDRESS BOOK