Sanyo DSR-3709 - Manual (Page 61)

60
English
SE
TTIN
GS
3
RECORD SET
The is used to make the following settings.
Use the following procedures to make simple recording
settings. Two different setting methods may be used -- one
based on recording days; the other based on recording rate.
z Before making easy setup settings, connect the
camera(s) to the digital video recorder and then always
perform “CAMERA DETECT”.
(J P.54)
z When easy setup settings and individual settings are both
set, the most recent settings override previous settings.
z Easy setup settings will be cancelled as a result of the
following operations.
(1) When the number of cameras detected using “CAMERA
DETECT” is greater or less than the number of cameras
previously stored in the digital video recorder.
(2) When the setting for “PRE-ALARM RECORDING” from
the screen is changed.
(3) When menu settings are loaded from a CompactFlash card.
(4) When a new easy setup setting operation is carried out.
(5) When setting values are changed for normal recording
or timer recording.
(6) When the area is changed using the
AREA SET> screen.
[EXIT/OSD] button
Jog dial
Shuttle dial
FULL indicator ALARM FULL indicator
[MENU] button
CARD CARD
MENU RESET
EJECT
[TIMER] button [CAMERA SELECT] buttons
MOVE:JOG SELECT:SHUTTLE
Main Menu
Settings for recording
Setting Description Ref
1
Makes basic settings based
on a number of days or a rate.
P.60
2
Displays the total capacity of
the hard disk.
Sets the normal recording
area, the alarm recording
area, and the archive area.
P.64
3
Sets whether overwriting is to be
performed (by deleting old video)
or recording is to be stopped
when any of the hard disk’s
recording areas become full.
Also sets the auto delete and
series recording.
P.67
4
Sets the picture quality, audio
recording, the recording rate,
and the program period.
P.71
5
Sets program recording for
cameras.
P.73
1.NORMAL REC EASY SET ->
2.RECORDING AREA SET ->
3.RECORDING CONDITIONS SET ->
4.NORMAL REC MODE SET ->
5.PROGRAM REC SET ->
6.TIMER SET ->
7.ALARM REC MODE SET ->
8.ALARM OPERATION SET ->
MOVE:JOG SELECT:SHUTTLE
RECORDING DURATION BASE ->
REC RATE BASE ->
CAUTION !
CONNECT CAMERA AND SET TIME
BEFORE SETUP
TOTAL CAPACITY : 82GB
NORMAL RECORDING AREA : 80 %
AREA FULL RESET ->
ALARM RECORDING AREA : 19 %
AREA FULL RESET ->
ARCHIVE AREA : 1 %
AREA FULL RESET ->
CAUTION : WHEN THE AREA SETTING IS CHANGED,
THE WHOLE AREA WILL BE INITIALIZED !
NORMAL RECORDING AREA
OVERWRITE : ON
ALARM RECORDING AREA
OVERWRITE : ON
REMAINING DISK WARNING : **
SERIES REC : OFF
AUTO DELETE : OFF
PICTURE QUALITY : ENHANCED
AUDIO RECORDING : OFF
REC RATE : 15FPS ( 35H)
REC PROGRAM GROUP : OFF
PROGRAM : P-1
SELECT INDIVIDUAL CAMERA RATE(FPS)
01: 0.5 02: 0.5 03: 0.5 04: 0.5
05: 0.5 06: 0.5 07: 0.5 08: 0.5
09: 0.5 10: 0.5 11: 0.5 12: 0.5
13: 0.5 14: 0.5 15: 0.5 16: 0.5
NORMAL REC : 65H
6
Makes timer settings so that
operations can be started at a
specified time or on a
specified day.
P.74
7
Sets alarm recording, pre-
alarm recording, and motion
sensors.
P.77
8
Makes settings for operation
and display upon detecting an
alarm.
P.84
Normal recording easy setup
Setting Description Ref
WEEK START STOP PROGRAM FPS SET
SUN --:-- --:-- OFF 15 FPS OFF
MON --:-- --:-- OFF 15 FPS OFF
TUE --:-- --:-- OFF 15 FPS OFF
WED --:-- --:-- OFF 15 FPS OFF
THU --:-- --:-- OFF 15 FPS OFF
FRI --:-- --:-- OFF 15 FPS OFF
SAT --:-- --:-- OFF 15 FPS OFF
DLY --:-- --:-- OFF 15 FPS OFF
EXT ***** ***** OFF 15 FPS OFF
ALARM RECORDING : OFF
PICTURE QUALITY : ENHANCED
AUDIO RECORDING : OFF
ALARM INTERLEAVE : ONLY
REC RATE: 15FPS, DURATION: 20SEC
PRE-ALARM RECORDING : ***
REC RATE: **** FPS, DURATION: ****
=> (01731 ALARMS CAN BE RECORDED)
ALARM TRIGGER : ALARM
MOTION SENSOR ->
ALARM RETRIGGER : OFF
MAIN MON. DISPLAY : NC
ALARM PRIORITY : LAST
MON.2 DISPLAY : OFF
e00_l8hbg_us_7.book Page 60 Thursday, November 25, 2004 1:44 PM