JVC BR-DV6000U - Manual (Page 38)

62
TC/UB/CLOCK(1/2) Menu screen
CH1/3
NDF 12
H
34
M
34
S
10
F EXT
CH2/4
STOP SP222 min
01/02/03
01:23:45
INS AM
OVER
48k
TC
L dB 0 10 20 30 40
OVER
W
Y/C
VA
SYNC
r
e
CF
STOP
K C A B E G A P
E G A P T X E N
F F O T E S F F O C T
F F O E T A C I L P U D C T
– – – ) L A P ( T I B F D
P O R D ) C S T N ( F D / F D N
N U R - C E R E D O M G C T
T E S E R P T C E L E S G C T
L A N R E T X E E C R U O S G C T
– – )– 2 / 1 ( K C O L C / B U / C T – – –
VIDEO LINE
IN
OUT
MONITOR OUT
DC12V
DV IN/OUT
IN OUT OFF
AUDIO
REMOTE2
IN B-Y R-Y
SYNC IN TIME CODE IN OUT
Y
COMPONENT
OUT CH 1/3 CH 2/4
IN
OUT
MONITOR OUT REMOTE1 TIMER
REC PLAY
SERIAL REMOTE SINGLE GND
Y/C
TIME CODE – Recording the time code – (continued)
Record time codes from an external time code generator
Synchronize the internal time code generator with the SMPTE-compliant LTC time code, which is
input from the TC IN terminal. After synchronization (slave lock), the internal time code generator
continues to run even if external time code signals are not input.
Memo
● If the phase of the external
time code generator and
the phase of the video are
not synchronized, the
“EXT” display blinks.
● If a user’s bit is input to the
TIME CODE IN terminal
with its all digits set as
“F”, BR-DV6000 converts
FFFFFFFF to FFFFFFFE
before recording.
: Connection :
Ⅵ Input reference video signals to the external time code
generator and the SYNC IN terminal of BR-DV6000.
Ⅵ Connect the TIME CODE IN terminal of BR-DV6000 with
the LTC time code output terminal of the external time
code generator.
: Setting :
Ⅵ Front switches
• Set the INPUT SELECT switch to any setting except DV.
• Set the COUNTER switch to “TC”.
• Press the DISP button and set the LCD to the enlarged display
mode.
Ⅵ TC/UB/CLOCK(1/2) Menu screen
Set TCG SOURCE to “EXTERNAL”.
: Operation :
1. Perform setting for the external time code generator.
2. Set BR-DV6000 to the RECORDING mode.
¥ The EXT display of the LCD lights up and the time code and
user’s bit of the external time code generator are recorded on
the tape.
During recording, if the internal time code generator is slave-
locked once, the time code continues to run even if the input
time code stops.
REF video
signal
Synchronized signal
generator
SYNC IN terminal
Time code generator
TIME CODE IN terminal LTC time code
EXT display
63
BR-DV6000
PROFESSIONAL RESET A.DUB
EJECT
COUNTER AUDIO INPUT SELECT MONITOR OUTPUT REMOTE
LOCAL
CTL L MIX R
CH-1/2 MIX CH-3/4
DV LINE Y/C (CPN)
TC
UB
REW STOP FF
REC
OPERATE
PLAY PAUSE DISP
SET INDEX+
BLANK CUE UP
REC LEVEL
CH-1/3 CH-2/4
3 2 K C H – 1 / 2 0 m S P i n 0 0
A S S E M
W A R N I N G 7 0 0 1
D R U M MO T O R F A I L U R E
R E C I N H I B I T
0 3 / 0 4 / 0 3 P L A Y
1 1 : 2 0 : 0 0 T C R 0 2 : 0 0 : 0 0 : 0 0
Monitor / LCD (Status display)
VIDEO LINE
IN
OUT
MONITOR OUT
DC12V
DV IN/OUT
IN OUT OFF
AUDIO
REMOTE2
IN B-Y R-Y
SYNC IN TIME CODE IN OUT
Y
COMPONENT
OUT CH 1/3 CH 2/4
IN
OUT
MONITOR OUT REMOTE1 TIMER
REC PLAY
SERIAL REMOTE SINGLE GND
Y/C
TIME CODE – Playing back the time code –
BR-DV6000 is also equipped with a time code reader. During playback, the time code or user’s bit
data recorded on the tape is displayed on the monitor or the LCD.
COUNTER switch TIME CODE OUT terminal
Time code or user’s bit
1. Select the time code data to display.
Set the COUNTER switch to “TC” or “UB”.
2. Press the PLAY button to go to the PLAYBACK mode.
¥ It displays the time code and the user’s bit on the monitor or
the LCD. The counter display mode becomes TCR or UBR.
• The LTC time code is output from the TIME CODE OUT terminal
on the rear panel.
❈ The VITC time code is not output.
If the COUNTER switch is set to CTL, the time code is not out-
put.
Caution on time code playback
● During playback, if a portion of tape without recorded time code
runs through, the time code stops running. Playback continues.
● If tapes without recorded user’s bit, e.g. those recorded with a
home-use DV VCR, are played back on BR-DV6000, “– –” is dis-
played.