beautypg.com

Torque requirements – Generac Power Systems Recreational Vehicle Generator 5413 User Manual

Page 79

background image

Section 10

SPECIFICATIONS & CHARTS

Page 77

TYPE

RV 45G/LP

RV 55G/LP

RV 65G/LP

MODEL

5410/5411

5412/5413

5414/5415

WEIGHT

278/281 pounds

285/288 pounds

293/296 pounds

TYPE OF ROTOR

Two-pole

Two-pole

Two-pole

RATED WATTS

4500

5500

6500

RATED VOLTS

120

120

120

PHASE

1-Phase

1-Phase

1-Phase

RATED MAx.
CONTINUOUS CURRENT
AMPS (240V)

37.5 (18.7)

45.8 (22.9)

54.1 (27)

RATED FREqUENCY

60 Hz

60 Hz

60 Hz

OPERATING SPEED

2571 rpm

2571 rpm

2571 rpm

ENGINE MODEL

GT-530

GT-530

GT-530

TYPE OF ENGINE

Vertical Shaft

Vertical Shaft

Vertical Shaft

FUEL SYSTEM

Gasoline/LP

Gasoline/LP

Gasoline/LP

COOLING SYSTEM

Air-Cooled

Air-Cooled

Air-Cooled

OIL SYSTEM

Pressurized with Filter

Pressurized with Filter

Pressurized with Filter

OIL PUMP

Trochoid Type

Trochoid Type

Trochoid Type

AIR CLEANER

Paper element

Paper element

Paper element

STARTER

12 VDC electric

12 VDC electric

12 VDC electric

IGNITION SYSTEM

Solid State/Flywheel

Magneto

Solid State/Flywheel

Magneto

Solid State/Flywheel

Magneto

SPARk PLUG

NGk BPR6HS

NGk BPR6HS

NGk BPR6HS

SPARk PLUG GAP

0.030 inch (0.76mm)

0.030 inch (0.76mm)

0.030 inch (0.76mm)

NOMINAL RESISTANCES OF gENERATOR WINdINgS AT 68°F

gENERATOR SPECIFICATIONS

TYPE

RV 45G/LP

RV 55G/LP

RV 65G/LP

MODEL

5410/5411

5412/5413

5414/5415

Power Windings
Lead 11 to 22
Lead 11S to 22S
Lead 33 to 44

0.376 - 0.416 ohms

0.28 - 0.32 ohms

0.209 - 0.242 ohms

Excitation “DPE” Winding
Lead 2 to 6

2.59 ohms

1.41 - 1.63 ohms

1.59 - 1.84 ohms

Rotor Winding
Slip Ring to Slip Ring

13.4 ohms

14.88 ohms

10.81 ohms

TORqUE REqUIREMENTS

(unless otherwise specified)

Stator Bolts ................................................................ 8 ft-lbs
Alternator Pulley ...................................................... 38 ft-lbs
Engine Pulley ........................................................... 38 ft-lbs
Oil Adaptor Bolt ...................................................... 4.5 ft-lbs
Oil Lines .................................................................. 70 in-lbs
Intake Manifold ........................................................ 18 ft-lbs
Exhaust Manifold ..................................................... 18 ft-lbs
M5-0.8 taptite screw into aluminum ................... 25-50 in-lbs
M5-0.8 taptite screw into pierced hole ............... 25-50 in-lbs

M6-1.0 taptite screw into aluminum ................... 50-96 in-lbs
M6-1.0 taptite screw into pierced hole ............... 50-96 in-lbs
M6-1.0 taptite screw into weldnut ...................... 50-96 in-lbs
M8-1.25 taptite screw into aluminum ................. 12-18 ft-lbs
M6-1.0 nylok nut onto stud ................................ 16-65 in-lbs
Dipstick Casting Oil Line ....................................... 250 in-lbs

Note: Torques are dynamic values with ±10 % tolerance
unless otherwise noted.