Lucent Technologies 6000 - Manual (Page 576)

Index-10 MAX 6000/3000 Network Configuration Guide
Index
K
IPX Route profiles , 12-3
static routes , 12-3
IPX routes
configuring , 12-6
IPX routing , 2-6
connections, configuring , 12-8
enabling , 12-5
NetWare clients , 12-4
network for dial-in clients, defining , 12-5
requirement of authentication , 12-2
Route IPX parameter , 4-18
IPX routing global parameters
IPX Frame , 12-5
IPX Pool # , 12-5
IPX Routing , 12-5
IPX SAP (Service Advertising Protocol) , 12-2
filters , 12-3 , 12-4
SAP packets, broadcast , 12-2
tables , 12-2
IPX SAP broadcasts
sending and receiving , 12-10
IPX SAP Filter parameter , 12-8
IPX SAP filters , 12-22
input , 12-23
output , 12-23
IPX SAP parameter , 12-9
IPX server bridge (local servers) , 14-15
IPX static route profiles
configuring , 12-21
IPX static routes
configuring , 12-19
IPX static routes, example , 12-22
IPX watchdog spoofing , 12-11 , 14-14
IPXCP , 12-1
IPXWAN , 12-1
ISDN
BRI network cards
configuring, 3-34
call information (E1) , 3-28
D-channel X.25 support, configuring , 6-30
PRI service, configuring , 3-13
signaling , 3-26
subaddressing parameters , 3-59
ISDN Digital Subscriber Line (IDSL)
diagnostics , 3-47
voice call support, configuring , 3-45
K
KeyID parameter , 8-11
L
L2TP (Layer 2 Tunneling Protocol) , 11-1
L2TP (Layer 2 Tunneling Protocol) tunnels
authentication , 11-33
client authentication , 11-33
configuring , 11-31
creating , 11-32
flow control , 11-34
for dial-in clients, configuring , 11-31
LAC and LNS mode , 11-33
MAX, functioning as a LAC , 11-36
L2TP Access Concentrator. See LAC
L2TP Auth Enabled parameter
, 11-36
L2TP Mode parameter , 11-36
L2TP Network Server. See LNS
L2TP RX Window parameter
, 11-36
LAC (L2TP Access Concentrator) , 11-31
MAX functioning as a , 11-36
mode , 11-33
LAN (Local Area Network) interface , 9-7
configurations for MAX stacks , 4-60
primary IP address , 9-7
secondary IP address , 9-7
LAN Adrs parameter , 5-19 , 5-22 , 6-10
LAN OSPF interfaces
designated router priority , 8-10
LAN parameter , 9-23
LAP (Link Access Procedure) , 6-3
LAPB (Link Access Procedure, Balanced) , 6-3
LAPB k parameter , 6-4
LAPB N2 parameter , 6-4
LAPB T1 parameter , 6-4
Layer 2 Tunneling Protocol. See L2TP
LCN parameter
, 6-8
LCP (Link Control Protocol) , 4-7 , 4-64
learning bridge , 14-4
Length parameter , 15-7
Line N Tunnel Type parameter , 11-36
line utilization
RADIUS attributes , 4-53
link management , 5-2 , 5-4
UNI interface , 5-2
Link Mgmt parameter , 5-6
Link Status Dlci parameter , 5-6
Link-State Advertisements (LSAs) , 8-6
link-state routing algorithm , 8-7
List Attempt parameter , 9-14
List Size parameter , 9-14
Listen command , 6-20