AERCO KC1000 Heater 2002 Instruction Manuals and User Guides

We have 1 Instruction Manual and User Guide for KC1000 Heater 2002 AERCO

AERCO KC1000 Heater 2002 User Manual, 106 pages

Recognized languages:	English
Pages:	106
Size:	2.62 MB

Show table of contents

Document Outline

KC-H-Cover-JAN-09_PN
- UTelephone Support
- Direct to AERCO Technical Support
KC-H-TOC-3-19-07
- FOREWARD A
- Section 1 – SAFETY PRECAUTIONS 1-1
- Section 2 – INSTALLATION PROCEDURES 2-1
- Section 3 – CONTROL PANEL OPERATING PROCEDURES 3-1
- Section 4 – INITIAL START-UP 4-1
- Section 5 – SAFETY DEVICE TESTING PROCEDURES 5-1
- Section 6 – MAINTENANCE 6-1
- Section 7 – TROUBLESHOOTING 7-1
- APPENDICES
- WARRANTIES W-1
KC-H-Foreward-10-2-06-J
KC-H-CH1-1-15-07-J
- 1.1 WARNINGS & CAUTIONS
- 1.2 EMERGENCY SHUTDOWN
- 1.3 PROLONGED SHUTDOWN
KC-H-Ch2-11-25-08
- 2.1 RECEIVING THE UNIT
- 2.2 UNPACKING
- 2.3 INSTALLATION
- 2.4 GAS SUPPLY PIPING
KC-H-Ch3-11-25-08
- Section 3 - CONTROL PANEL OPERATING PROCEDURES
KC-H-Ch4-11-25-08
- 4.2.2 INSTALLING THE SUPPLY GAS MANOMETER
  - Figure 4.1
    - 1/4” Gas Plug Location
- 4.2.3 PREPARING THE FLUE VENT PROBE HOLE
  - Figure 4.2
    - Analyzer Probe Hole Location
- 4.2.4 INSTALLING THE DIFFERENTIAL REGULATOR ADJUSTMENT TOOL
  - Figure 4.3
    - Differential Regulator Adjustment Tool Installation
- 4.3 NATURAL GAS COMBUSTION CALIBRATION
  - Air Shutter Locking Nut Location
- 4.4 PROPANE COMBUSTION CALIBRATION
  - Figure 4.5
    - Propane Air Differential Pressure Taps
- 4.6 TEMPERATURE CONTROL CALIBRATION
- 4.7 OVER-TEMPERATURE LIMIT SWITCH ADJUSTMENTS
  - Figure 4.6
    - Over Temperature Limit Switch Location
KC-H-Ch5--2-26-07
- SECTION 5 - SAFETY DEVICE TESTING PROCEDURES
KC-H-Ch6-GF111_12-09-10
- 6.1 MAINTENANCE SCHEDULE
- 6.2 Spark Ignitor
  - Figure 6.1
    - Spark Ignitor and Flame Detector Location
- 6.3 Flame Detector
- 6.4 COMBUSTION CALIBRATION
- 6.5 SAFETY DEVICE TESTING
  - 6.6 BTU TRANSMITTER PUMP LUBRICATION
  - Figure 6.2
    - BTU Transmitter Pump Oil Port Locations
- 6.7 BTU TRANSMITTER ASSEMBLY
- 6.8 MANIFOLD AND EXHAUST TUBES
- 6.9 HEAT EXCHANGER INSPECTION AND CLEANING
- 6.10 CONDENSATE DRAIN ASSEMBLY
- 6.11 LOW WATER CUTOFF PROBE INSPECTION AND CLEANING
- 6.12 HYDRAULIC ZERO NEEDLE VALVE ADJUSTMENT (C-More Control BOX)
- 6.13 FLAME STRENGTH MEASURMENT
KC-H-Ch7_09-29-10
- SECTION 7- TROUBLESHOOTING GUIDE
  - 7.1 INTRODUCTION
- 1. Inspect feed forward (BTU transmitter) sensor for loose or broken wiring.
- 2. Check resistance of sensor to determine if it is within specification.
- 1. Measure the actual exhaust temperature and continuity of the exhaust sensor. If the exhaust temperature is less than 500 o F and the exhaust sensor shows continuity replace the sensor.
- 2. If exhaust temperature is greater than 500 o F, check combustion calibration. Calibrate or repair as necessary.
- KC1000 WATER HEATER TROUBLESHOOTING TABLE – Continued
- KC1000 WATER HEATER TROUBLESHOOTING TABLE – Continued
- KC1000 WATER HEATER TROUBLESHOOTING TABLE – Continued
KC-H-App-A-11-25-08
KC-H-App-B
KC-H-App-C
KC-H-App-D-JULY-06
KC-H-App-E--4-25-07-A
KC-H-App-F-11-30-06
KC-H-App-G-JULY-06
KC-H-App-H-12-27-08
KC-B-App-I-12-27-08
KC-HTR-WARRANTY

Popular Brands

Popular manuals