Sealey VS0561 - Manual

INSTRUCTIONS FOR
DIGITAL BRAKE Disc
CALLIPER 100mm/4”
Model No:
VS0561
Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions and
properly maintained, give you years of trouble free performance.
IMPORTANT
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS, AND CAUTIONS.
USE THIS PRODUCT CORRECTLY AND WITH CARE, FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE
DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY.
p p WARNING! Ensure Health and Safety, local authority and general workshop practice regulations are adhered to
when using tools and equipment.
7 DO NOT use calliper if damaged.
3 Maintain calliper in good and clean condition for best and safest performance.
3 Keep the work area clean, uncluttered and ensure there is adequate lighting.
3 Keep children and unauthorised persons away from the work area.
7 DO NOT use the calliper for any purpose other than for which it is designed.
7 DO NOT get calliper wet or use in damp or wet locations, or areas where there is condensation. Keep calliper clean and dry
using a dry cotton cloth only.
7 DO NOT dip or submerge the calliper in any type of liquid.
7 DO NOT expose calliper to bright sunlight or dust.
7 DO NOT dis-assemble calliper. The calliper must be checked by qualified service personnel only.
7 DO NOT apply any voltage to the calliper i.e. with an electric marker pen.
3 The calliper is a precision instrument. Treat with care, avoid using force and do not subject to knocks or shocks.
3 Take particular care not to damage or scratch the scale surface.
3 Use calliper in reasonably constant temperature conditions of approximately 20 O C.
3 When not in use, turn off and store calliper in a safe, dry, childproof location.
1. SAFETY INSTRUCTIONS
1 “ON/OFF”
2 “mm/inch”
3 RS-232 connection
4 Battery cover
5 “ZERO”
6 Thumb wheel
7 “HOLD”
2. INTRODUCTION & SPECIFICATION
Hardened and tempered stainless steel gauge, 11mm high figures in LCD display for ease of reading. Metric or Imperial read-out
with ‘Hold’ function. Zero setting control allows for comparative measurement. Include serial port connection for computer
interface. Supplied in carry case.
Specification Vernier Calliper
Resolution 0.01mm (0.0005”)
Range 0-100mm (0-4”)
Accuracy ±0.02mm (±0.001”)
Functions Zero set, mm/inch select, Hold
Battery type SR44 (1.5V)
Operating temp 0 - +40°
VS0561 - 1 - 120804
Fig.1.
INSTRUCTIONS FOR
DIGITAL BRAKE Disc
CALLIPER 100mm/4”
Model No:
VS0561
Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions and
properly maintained, give you years of trouble free performance.
IMPORTANT
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS, AND CAUTIONS.
USE THIS PRODUCT CORRECTLY AND WITH CARE, FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE
DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY.
p p WARNING! Ensure Health and Safety, local authority and general workshop practice regulations are adhered to
when using tools and equipment.
7 DO NOT use calliper if damaged.
3 Maintain calliper in good and clean condition for best and safest performance.
3 Keep the work area clean, uncluttered and ensure there is adequate lighting.
3 Keep children and unauthorised persons away from the work area.
7 DO NOT use the calliper for any purpose other than for which it is designed.
7 DO NOT get calliper wet or use in damp or wet locations, or areas where there is condensation. Keep calliper clean and dry
using a dry cotton cloth only.
7 DO NOT dip or submerge the calliper in any type of liquid.
7 DO NOT expose calliper to bright sunlight or dust.
7 DO NOT dis-assemble calliper. The calliper must be checked by qualified service personnel only.
7 DO NOT apply any voltage to the calliper i.e. with an electric marker pen.
3 The calliper is a precision instrument. Treat with care, avoid using force and do not subject to knocks or shocks.
3 Take particular care not to damage or scratch the scale surface.
3 Use calliper in reasonably constant temperature conditions of approximately 20 O C.
3 When not in use, turn off and store calliper in a safe, dry, childproof location.
1. SAFETY INSTRUCTIONS
1 “ON/OFF”
2 “mm/inch”
3 RS-232 connection
4 Battery cover
5 “ZERO”
6 Thumb wheel
7 “HOLD”
2. INTRODUCTION & SPECIFICATION
Hardened and tempered stainless steel gauge, 11mm high figures in LCD display for ease of reading. Metric or Imperial read-out
with ‘Hold’ function. Zero setting control allows for comparative measurement. Include serial port connection for computer
interface. Supplied in carry case.
Specification Vernier Calliper
Resolution 0.01mm (0.0005”)
Range 0-100mm (0-4”)
Accuracy ±0.02mm (±0.001”)
Functions Zero set, mm/inch select, Hold
Battery type SR44 (1.5V)
Operating temp 0 - +40°
VS0561 - 1 - 120804
Fig.1.