Warranty information – Sealey VS0271 User Manual
Page 2
VS0271 - 2 - 27/05/04
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts
without prior notice.
IMPORTANT: No liability is accepted for incorrect use of this product.
WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
INFORMATION: For a copy of our catalogue and promotions call 01284 757525 and leave your full name and address, including postcode.
www.sealey.co.uk
01284 757500
01284 703534
Web
Sole UK Distributor
Sealey Group,
Bury St. Edmunds, Suffolk.
3.04 Remove the cap from the vehicles master cylinder reservoir and ensure that the battery
terminals are clean and accessible for connection when required.
3.05 Uncoil the cable from the unit and remove the protective cap from the probe tip (1).
3.06 Connect the cable clamps to the battery ensuring correct polarity (2). (Red clamp to the
positive + terminal and the black clamp to the negative - terminal.)
3.07 Immerse the probe tip into the brake fluid to the required depth of 25mm. To get an accurate
reading the control switch should be held on for 30 seconds (3). At the end of this period
release the switch, observe the temperature readout and refer to the chart below.
3.08 Lift the probe up from the brake fluid reservoir and allow the fluid contained within the tip to drain
back into the reservoir (4). Before moving the tester away from the reservoir wipe excess fluid
from the tip to avoid dripping brake fluid onto any paintwork (5).
3.09 Replace the protective cap onto the probe tip and recoil the cable around the unit (6).
Replace the unit into the carry case together with any accessories and store safely.
4. WARRANTY INFORMATION
Sealey Power Products warrants this product to be free from defects in material and
workmanship under normal use and service for a period of one year from date of purchase,
except as hereinafter provided. In the event of a dispute regarding warranty, Sealey Power
Products would require proof of purchase displaying the purchase date, customer name,
product description and serial number of the unit. This warranty extends only to the original
purchase (a purchase from Sealey Power Products' licensed distributors is an original
purchase). This warranty shall not apply to fuses or batteries. Factory calibration is
warranted for a period of one year. The warranty shall not apply to any product that has
been subject to misuse, neglect, accident or abnormal renditions of operation or storage.
Should Sealey Power Products be unable to repair or replace the product within a
reasonable amount of time, purchaser's exclusive remedy shall be a refund of the purchase
price upon return of the product.
In the event of failure of a product covered by this warranty. Sealey Power Products will
repair the instrument when it is returned by the purchaser, at the purchaser's cost to Sealey
Power Products within the applicable warranty period, provided Sealey Power Products'
examination discloses to its satisfaction that the product was defective. Sealey Power
Products may, as its option, replace the product in lieu of repair. With regard to any
instrument returned within the applicable warranty period, repairs or replacement will be
made without charge and with return freight paid by Sealey Power Products. If the failure
was caused by misuse, neglect, accident, abnormal conditions of operation or storage,
repairs and return carriage charges will be billed at a reasonable cost. If purchaser tampers
with the product or attempts to carry out a repair themselves, the warranty will be void.
The foregoing warranty is in lieu of all other warranties, expressed or implied, including but
not limited to any implied warranty of merchantability, fitness or adequacy for any particular
purpose or use. Sealey Power Products shall not be liable for any special, incidental, or
consequential damages, whether in contract, tort or otherwise.
Temperature range
230
O
C † ‡
200
O
C † ‡
180
O
C † ‡
155
O
C
FLUID CONDITION GOOD
POOR
UNSAFE
FLUID RENEWAL
Not necessary Recommended IMMEDIATE
VS0271 - 2 - 27/05/04
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts
without prior notice.
IMPORTANT: No liability is accepted for incorrect use of this product.
WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
INFORMATION: For a copy of our catalogue and promotions call 01284 757525 and leave your full name and address, including postcode.
www.sealey.co.uk
01284 757500
01284 703534
Web
Sole UK Distributor
Sealey Group,
Bury St. Edmunds, Suffolk.
3.04 Remove the cap from the vehicles master cylinder reservoir and ensure that the battery
terminals are clean and accessible for connection when required.
3.05 Uncoil the cable from the unit and remove the protective cap from the probe tip (1).
3.06 Connect the cable clamps to the battery ensuring correct polarity (2). (Red clamp to the
positive + terminal and the black clamp to the negative - terminal.)
3.07 Immerse the probe tip into the brake fluid to the required depth of 25mm. To get an accurate
reading the control switch should be held on for 30 seconds (3). At the end of this period
release the switch, observe the temperature readout and refer to the chart below.
3.08 Lift the probe up from the brake fluid reservoir and allow the fluid contained within the tip to drain
back into the reservoir (4). Before moving the tester away from the reservoir wipe excess fluid
from the tip to avoid dripping brake fluid onto any paintwork (5).
3.09 Replace the protective cap onto the probe tip and recoil the cable around the unit (6).
Replace the unit into the carry case together with any accessories and store safely.
4. WARRANTY INFORMATION
Sealey Power Products warrants this product to be free from defects in material and
workmanship under normal use and service for a period of one year from date of purchase,
except as hereinafter provided. In the event of a dispute regarding warranty, Sealey Power
Products would require proof of purchase displaying the purchase date, customer name,
product description and serial number of the unit. This warranty extends only to the original
purchase (a purchase from Sealey Power Products' licensed distributors is an original
purchase). This warranty shall not apply to fuses or batteries. Factory calibration is
warranted for a period of one year. The warranty shall not apply to any product that has
been subject to misuse, neglect, accident or abnormal renditions of operation or storage.
Should Sealey Power Products be unable to repair or replace the product within a
reasonable amount of time, purchaser's exclusive remedy shall be a refund of the purchase
price upon return of the product.
In the event of failure of a product covered by this warranty. Sealey Power Products will
repair the instrument when it is returned by the purchaser, at the purchaser's cost to Sealey
Power Products within the applicable warranty period, provided Sealey Power Products'
examination discloses to its satisfaction that the product was defective. Sealey Power
Products may, as its option, replace the product in lieu of repair. With regard to any
instrument returned within the applicable warranty period, repairs or replacement will be
made without charge and with return freight paid by Sealey Power Products. If the failure
was caused by misuse, neglect, accident, abnormal conditions of operation or storage,
repairs and return carriage charges will be billed at a reasonable cost. If purchaser tampers
with the product or attempts to carry out a repair themselves, the warranty will be void.
The foregoing warranty is in lieu of all other warranties, expressed or implied, including but
not limited to any implied warranty of merchantability, fitness or adequacy for any particular
purpose or use. Sealey Power Products shall not be liable for any special, incidental, or
consequential damages, whether in contract, tort or otherwise.
Temperature range
230
O
C † ‡
200
O
C † ‡
180
O
C † ‡
155
O
C
FLUID CONDITION GOOD
POOR
UNSAFE
FLUID RENEWAL
Not necessary Recommended IMMEDIATE