Sealey TA202 - Manual (Page 4)

4.13. Other Functions
4 .13 .1 . Your meter is also capable of testing the following automotive sensors .
Oxygen Sensors
Fuel Injectors
Temp Sensors
Position Sensors
absolute pressure (MAP) and Baro Sensors
Mass Air Flow (MAF) Sensors
4 .13 .2 . For a detailed description and testing procedure for these sensors, please refer to the vehicles hand book .
4.14. Replacing The Battery
 WARNING! To avoid electric shock, disconnect the test leads from any source of voltage before removing the battery door.
4 .14 .1 . When the battery become exhausted or drops below the operating voltage, “BAT” will be appear in the right hand side of the display . Replace the battery .
4 .14 .2 . Disconnect the leads from the meter .
4 .14 .3 . Open the battery door by loosening the screw using a Philips head screw driver .
4 .14 .4 . Remove the old battery and insert the new one, observing the correct polarity .
4 .14 .5 . Replace the battery cover and secure with the two screws .

WARNING! To avoid electric shock, DO NOT operate the meter until the battery cover is secured in place.
4.15. Replacing The Fuses
 WARNING! To avoid electric shock, disconnect the test leads from any source of voltage before accessing the fuses.
4 .15 .1 . Disconnect the test leads from any item under test and disconnect them from the meter .
4 .15 .2 . Remove the 5 screws on the rear of the meter and gently pull the two halves of the meter apart .
4 .15 .3 . Remove the old fuse from its holder by gently pulling it out .
4 .15 .4 . Install the new fuse into its holder .
Note: Always use a fuse of the correct size and value .
0 .5A/250V fast blow for the 400mA range .
20A/250V fast blow for the 10A range .
4 .15 .5 . Put the two halves of the meter back together and secure with the 5 screws .

WARNING! To avoid electric shock, DO NOT use the meter until it has been fully re-assembled.
Item Description Parts
1 TA202 .01 TEMPERATURE PROBE
2 TA202 .02 TEST LEADS
 WARNING! DO NOT attempt to repair or service your meter unless you are qualified to do so and have the relevant calibration, performance test,
and service information . To avoid electrical shock or damage to the meter do not get water inside the case .
5.1. Periodically wipe the case with a damp cloth and mild detergent . Do not use solvents .
5.2. Turn the meter off when not in use and remove the battery if stored for a long period of time .
5.3. Do not store the meter in a place of high humidity or high temperature
ISSUE 1
ISSUE DATE 220404
Environmental Protection
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to
a recycle centre and disposed of in a manner which is compatible with the environment.
WEEE Regulations
Dispose of this product at the end of its working life in compliance with the EU Directive on
Waste Electrical and Electronic Equipment (WEEE). When the product is no longer required, it must be disposed
of in an environmentally protective way. Contact your local solid waste authority for recycling information.
Battery Removal: See Section 4.14.
ONLY dispose of or recycle according to local authority regulations. Under the Waste Batteries and Accumulators Regulations 2009,
Jack Sealey Ltd are required to inform potential purchasers of products containing batteries (as defined within these regulations),
that they are registered with Valpak’s registered compliance scheme. Jack Sealey Ltd’s Batteries Producer Registration Number
(BPRN) is BPRN00705.
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT: No liability is accepted for incorrect use of this product .
WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim .
INFORMATION: For a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode .
01284 757500
01284 703534 sales@sealey .co .uk
Sole UK Distributor, Sealey Group,
Kempson Way, Suffolk Business Park ,
Bury St . Edmunds, Suffolk,
IP32 7AR
www .sealey .co .uk
Original Language Version © Jack Sealey Limited
6. PARTS
5. MAINTENANCE
TA202 Issue No: 3(L) - 17/06/14