Sealey TC966 - Manual

InstructIons for:
Hydraulic bead breaker
MoDEL: Tc966
thank you for purchasing a sealey product. Manufactured to a high standard this product will, if used according to these instructions
and properly maintained, give you years of trouble free performance.
1. SaFeTy iNSTrucTiONS
IMPORTANT: PleaSe read THeSe iNSTrucTiONS careFully. NOTe THe SaFe OPeraTiONal reQuireMeNTS, WarNiNGS aNd cauTiONS.
uSe THe PrOducT cOrrecTly aNd WiTH care FOr THe PurPOSe FOr WHicH iT iS iNTeNded. Failure TO dO SO May cauSe
daMaGe aNd/Or PerSONal iNJury aNd Will iNValidaTe THe WarraNTy. PleaSe keeP iNSTrucTiONS SaFe FOr FuTure uSe.
610/40 610/42 rE83/840/cWH
2. SPeciFicaTiONS
Hydraulic action, suitable for breaking beads on commercial and
agricultural tyres. use in conjunction with hydraulic pump and hose
(not included).

WarNiNG! dO NOT use on split, multi-piece or rims greater
than 26".
1.1 GeNeral SaFeTy

WarNiNG! Ensure Health & Safety, local authority, and general workshop practice regulations are adhered to when using this equipment.
Under Health and Safety Law, Employers and Self Employed Personnel have a legal duty to ensure Safe Working Conditions for all
employees and personnel that may come into contact with this equipment. In particular they must carry out a specific risk and hazard
assessment in the workplace to eliminate or reduce any risk found and must record, update and retain records of the results of this
inspection.

familiarise yourself with the applications, limitations and any possible or potential hazards of the Bead Breaker.

Maintain the Bead Breaker in good condition (use an authorised service agent).

WarNiNG! The tyre must be deflated before using the bead breaker. Failure to heed this warning, could result in injury.

replace or repair damaged parts. Use genuine parts only. Unauthorised parts may be dangerous and will invalidate the warranty.

WarNiNG! check regularly for damaged parts. Any part that is damaged must be repaired or replaced before the equipment is next used.

use the Bead Breaker in a suitable work area, keep area clean and tidy and free from unrelated materials. Ensure that there is adequate
lighting.

Keep the Bead Breaker clean for best and safest performance.

Wear approved safety eye protection.

Keep hands well clear of the bead breaker.

Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip safety shoes.

remove ill fitting clothing. remove ties, watches, rings other loose jewellery and contain and/or tie back long hair.

Keep hands away from pinch and crush points that can be created during operation.

Keep children and unauthorised persons away from the work area.

WarNiNG! dO NOT use on split, multi-piece or rims greater than 26".

dO NOT use the Bead Breaker for any purpose other than that for which it is designed.

dO NOT operate the Bead Breaker if any parts are damaged or missing as this may cause failure and/or personal injury.

dO NOT allow untrained persons to operate the Bead Breaker.

dO NOT operate the Bead Breaker when you are tired or under the influence of alcohol, drugs or intoxicating medication.
 dO NOT top up system with brake fluid. Use hydraulic oil only.
 dO NOT adjust the safety overload valve.
 When not in use clean the Bead Breaker and store in the open position
in a safe, dry, child-proof area.
optional Hydraulics:
Option 1
foot operated Air Hydraulic Pump With Hose: .......rE83/840/cWH
Option 2
Pump: ............................................. 610/40
Hose with Half coupling: ................ 610/42
foot
claw
Handle
cylinder
oil Port
cylinder
Handle
shovel
foot

WarNiNG! The warnings, cautions and instructions referred to in this manual cannot cover all
possible conditions and situations that may occur. It must be understood that common sense and
caution are factors which cannot be built into this product, but must be applied by the operator.
tc966 Issue no. 1 - 24/11/08