Sealey VS0041 - Manual

IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS AND CAUTIONS. USE THIS PRODUCT
CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL
INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY INSTRUCTIONS
2. INTRODUCTION & SPECIFICATION
 Follow all workshop, Health & Safety rules, regulations and conditions when using this equipment.
 WARNING! Disconnect from the air supply before changing accessories or servicing.
 Maintain the equipment in good condition and replace any damaged or worn parts. Use genuine parts only. Unauthorised parts may be
dangerous and will invalidate the warranty.

WARNING! Check that correct air pressure is maintained and DOES NOT exceed 100psi.
 Keep air hose away from heat, oil and sharp edges. Check air hose for wear before each use and ensure that all connections are secure.
 Wear approved safety gloves and eye and ear protection (available from your Sealey supplier).
 Keep this tool clean and in good working order for best and safest performance.
 DO NOT use the tool for a task it is not designed to perform.
 WARNING! DO NOT use the tool if it is damaged or thought to be faulty. Contact your local service agent.
 DO NOT drop, throw or abuse the tool.
 DO NOT carry the tool by the air hose, or yank the hose from the air supply.
 DO NOT operate if you are tired or under the influence of alcohol, drugs or intoxicating medication.
 DO NOT direct air from the air hose, at yourself or others.
 Keep children and unauthorised persons away from the work area.
 When not in use, disconnect from the air supply and store in a safe, dry, childproof location.
 WARNING! The warnings, cautions and instructions discussed in this instruction manual cannot cover all possible conditions and situations that
may occur. It must be understood that common sense and caution are factors which cannot be built into this product, but must be applied by
the operator.
INSTRUCTIONS FOR:
COOLING SYSTEM FILLER
MODEL NO:
VS0041.V2
Thankyou for purchasing a Sealey Product. Manufactured to a high standard this product will, if used according to these instructions and properly
maintained, give you years of trouble free performance.
Eliminates the introduction of bubbles and air-locks into the cooling system and dramatically reduces system filling time. No more time-consuming
system bleeding. Reduces fluid waste and messy spills. Automatically conducts system leak test. Low profile design broadens application range
especially for use on MPV's where lower windscreen lip might obstruct other tools. Simple operation requires workshop air supply and does not
require fiddly interchange of vacuum and fluid hoses - as found on other versions of this tool. Supplied with 1300mm fluid hose.
3.1. Recommended hook-up is shown in fig.2.
Ensure that both coolant and vacuum taps are in the
‘off’ position (fully to the left or right) when connecting
the air supply. Fig.1. shows both taps in the open
position (in-line with the outlet/inlet pipe).
 WARNING! Ensure that the air supply is clean and
does not exceed 100psi. Too high an air pressure or
unclean air will shorten the life of the filler due to
excessive wear, and may be dangerous, causing
damage and/or personal injury.
3.2. Drain the air tank on the compressor daily.
3.3. Clean compressor air inlet filter weekly.
3.4. Line pressure should be increased to compensate for
unusually long air hoses (over 8 metres). The minimum
hose size should be ¼” I.D. and fittings must have
the same internal bore.
3.5. Keep hose away from heat, oil and sharp edges.
Check hose for wear and make certain that all
connections are secure.
3. AIR SUPPLY
Operating Air Pressure: . . . . 80 - 100psi (5.5 - 6.9 bar)
Air Consumption: . . . . . . . . . . . . . . . . . . . . . . . . 12cfm
Connection: . . . . . . . . . . . . . . . . . . . . . . . . . . . .¼”BSP
Fluid Hose Length: . . . . . . . . . . . . . . . . . . . . 1300mm
fig.1
VS0041.V2 Issue No: 2 - 28/03/12
Original Language Version
fig.2