Sealey SA291 - Manual

Thank you for purchasing a Sealey Product. Manufactured to a high standard this product will, if used according to these instructions
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS,
WARNINGS AND CAUTIONS. USE THIS PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH
IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE
THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY INSTRUCTIONS
 Follow all workshop safety rules, regulations and conditions when using wrench.

WARNING! Disconnect from air supply before changing accessories or servicing.

Maintain the wrench in good condition and replace any damaged or worn parts. Use
genuine parts only. Unauthorised parts may be dangerous and will invalidate the warranty.

WARNING! Check correct air pressure is maintained and not exceeded. We recommend 90psi.

Keep air hose away from heat, oil and sharp edges. Check air hose for wear before each
use and ensure that all connections are secure.

Only use impact sockets which are specifically designed for use with an impact wrench.
 Wear approved safety eye/face shield, ear defenders and hand protection.

WARNING! Due to the possible presence of asbestos dust from brake linings, when working
around vehicle brake systems we recommend you wear suitable respiratory protection.

Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.

Keep children and non essential persons away from the working area.

DO NOT use the wrench for a task it is not designed to perform.

WARNING! DO NOT use wrench if damaged or thought to be faulty. (Contact Service Agent).

DO NOT use wrench unless you have been instructed in its use by a qualified person.

DO NOT carry the wrench by the air hose, or yank the hose from the air supply.

DO NOT operate wrench if you are tired or under the influence of alcohol, drugs or intoxicating
medication.

DO NOT carry wrench with your finger on the power trigger in order to avoid unintentional starting.

DO NOT direct air from the air hose at yourself or others.

When not in use disconnect from air supply and store in a safe, dry, childproof location.

WARNING! The warnings, cautions and instructions discussed in this manual cannot
cover all possible conditions and situations that may occur. It must be understood that
common sense and caution are factors which cannot be built into this product, but must be
applied by the operator.
2. INTRODUCTION & SPECIFICATION
Drive size . . . . . . . . . . . . . . . . . . . . . . . . . . 1”Sq
Working Max torque . . . . . . . . . . 1200/1350lb.ft
Ultimate torque . . . . . . . . . . . . . . . . . . . 1600lb.ft
Free Speed. . . . . . . . . . . . . . . . . . . . . .3500rpm
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . 14.2kg
Air consumption . . . . . . . . . . . . . . . . . . . 21cfm
Operating pressure. . . . . . . . . . . . 90psi
Air inlet size . . . . . . . . . . . . . . .1/2”BSP
Noise Power . . . . . . . . . . . . 98.76dB(A)
Noise Pressure. . . . . . . . . . 87.76dB(A)
Vibration . . . . . . . . . . . . . . . . . 8.44m/s²
Uncertainty . . . . . . . . . . . . . . . .0.81m/s²
Suitable for heavy commercial tyre shop, fleet and workshop use. Features air/torque device, to
control power output, and reverse action. Long pattern anvil gets into deeply dished wheels.
Supplied with side handle.
Original Language Version SA291.V3 Issue: 5(SP)- 12/11/13
INSTRUCTIONS FOR:
1” SQ DRIVE EXTRA HEAVY DUTY
IMPACT WRENCH, LONG ANVIL
MODEL No:
SA291.V3
© Jack Sealey Limited