Sealey SA53 - Manual

Suitable for cutting straight lines in metal sheet. Palm throttle control and alloy head and housing. Blades are
consumable items and are not covered by warranty.
Thank you for purchasing a Sealey Product. Manufactured to a high standard this product will, if used according to these instructions
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS,
WARNINGS AND CAUTIONS. USE THIS PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH
IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE
THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY INSTRUCTIONS
p WARNING! Ensure health & safety, local authority, and general workshop practice regulations are adhered to
when using this equipment.
p WARNING! Disconnect from air supply before changing accessories or servicing.
3 Maintain the tool in good condition and replace any damaged or worn parts. Use genuine parts only.
Unauthorised parts may be dangerous and will invalidate the warranty.
p
WARNING! Check correct air pressure is maintained and not exceeded. We recommend 90psi.
3 Keep air hose away from heat, oil and sharp edges. Check air hose for wear before each use and ensure that
all connections are secure.
3 Wear approved safety eye/face shield, ear defenders, and hand protection.
3 Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.
3 Keep children and non essential persons away from the working area.
7 DO NOT use the tool for a task it is not designed to perform.
p WARNING! DO NOT use tool if damaged or thought to be faulty. (Contact Sealey service agent).
7 DO NOT use tool unless you have been instructed in its use by a qualified person.
7
DO NOT carry the tool by the air hose, or yank the hose from the air supply.
7
DO NOT operate tool if you are tired or under the influence of alcohol, drugs or intoxicating medication.
7 DO NOT carry tool with your hand on the power trigger in order to avoid unintentional starting.
7 DO NOT direct air from the air hose at yourself or others.
3 When not in use disconnect from air supply and store in a safe, dry, childproof location.
INSTRUCTIONS FOR:
AIR SHEARS
MODEL No:
SA53.V3
2. INTRODUCTION & SPECIFICATIONS
Maximum cutting capacity . . . . . . . . 1.2mm(Steel)
Air consumption . . . . . . . . . . . . . . . . . . . . . . .4cfm
Operating pressure. . . . . . . . . . . . . . . . . . . . 90psi
Air inlet size . . . . . . . . . . . . . . . . . . . . . . 1/4” BSP
3. PREPARING TOOL FOR USE
3.1. Air Supply
3.1.1. Ensure tool valve (or trigger) is in the "off" position before connecting to the air supply.
3.1.2. You will require an air pressure of 90psi, and an air flow according to specification.
3.1.3. p WARNING! Ensure the air supply is clean and does not exceed 90 psi while operating the tool.
Too high an air pressure and unclean air will shorten the product life due to excessive wear, and may be
dangerous causing damage and/or personal injury.
3.1.4. Drain the air tank daily. Water in the air line will damage the tool.
3.1.5. Clean air inlet filter weekly. Recommended hook-up procedure is shown in fig 1.
3.1.6. Line pressure should be increased to compensate for unusually long air hoses (over 8 metres).
The minimum hose diameter should be 1/4” I.D. and fittings must have the same inside dimensions.
3.1.7. Keep hose away from heat, oil and sharp edges. Check hose for wear, and make certain that all
connections are secure.
3.2. Couplings.
Vibration may cause failure if a quick change coupling is connected directly to the tool. To overcome this,
connect a leader hose to the tool. A quick change coupling may then be used to connect the leader hose to the
air line recoil hose. See fig 1 & 2.
Original Language Version SA53.V3 Issue: 1 - 16/08/11
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.0kg
Noise Power . . . . . . . . . . . . . . . . . . . . . . . . 85dB.A
Replacement Blade - Right . . . . . . . . SA53.V3-30
Replacement Blade - Left. . . . . . . . . . SA53.V3-31
Replacement Blade - Centre . . . . . . . SA53.V3-32