Sealey SA2501 - Manual

Thank you for purchasing a Sealey Product. Manufactured to a high standard this product will, if used according to these instructions
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS,
WARNINGS AND CAUTIONS. USE THIS PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH
IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE
THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY INSTRUCTIONS

WARNING! Ensure that Health & Safety, local authority, and general workshop practice regulations are
adhered to when using this equipment.

WARNING! Disconnect from air supply before changing accessories or servicing.

Maintain the cut-off tool in good condition (use an authorised service agent).

Replace or repair damaged parts. Use genuine parts only. Unauthorised parts may be dangerous and will
invalidate the warranty.

Use in a suitable work area. Keep area free from unrelated materials and ensure that there is adequate lighting.

Before each use check cutting disc for condition. If worn or damaged replace immediately.

Ensure that the speed rating (rpm) of the disc is the same as, or greater than, the speed rating of the cut off saw.

Ensure that there are no flammable or combustible materials near the work area.

WARNING! Always wear approved eye (or face) and hand protection when operating the cut-off tool.

Use face, dust, or respiratory protection in accordance with COSHH regulations.

Depending on the task, the cut-off tool noise level may exceed 98dB in which case wear safety ear defenders.

Remove ill fitting clothing. Remove ties, watches, rings and other loose jewellery and contain and/or tie back long
hair.

Wear appropriate protective clothing and keep hands and body clear of working parts.

Maintain correct balance and footing. Ensure that the floor is not slippery and wear non-slip shoes.

Keep children and unauthorised persons away from the work area.

Check moving parts alignment on a regular basis.

Ensure that the workpiece is secure before operating the air cut-off tool. Never hold a workpiece by hand.

Check the workpiece to ensure there are no protruding screws, bolts, nuts etc.

Avoid unintentional starting.

WARNING! Ensure correct air pressure is maintained and not exceeded. Recommended pressure 90psi

Keep air hose away from heat, oil and sharp edges. Check air hose for wear before each use and ensure
that all connections are secure.

Prolonged exposure to vibration from this tool poses a health risk. It is the owner’s responsibility to correctly
assess the potential hazard and issue guidelines for safe periods of use and offer suitable protective equipment.

DO NOT use the cut-off tool for a task it is not designed to perform.

DO NOT operate cut-off tool if any parts are damaged or missing as this may cause failure and/or personal injury.

WARNING! DO NOT grind any materials containing asbestos.

DO NOT carry the cut-off tool by the hose, or yank the hose from the air supply.

DO NOT force, or apply heavy pressure to, the cut-off tool, let the tool do the work.

DO NOT place air line attachments close to your face and do not point them at other people or animals.

DO NOT operate cut-off tool when you are tired or under the influence of alcohol, drugs or intoxicating medication.

DO NOT use the cut-off tool where there are flammable liquids, solids or gases, such as paint solvents
and including waste wiping or cleaning rags etc.

DO NOT carry the cut-off tool with your finger on the power lever.

DO NOT direct air from the air line at yourself or others.

When not in use disconnect from air supply and store in a safe, dry, childproof location.
DANGER OF FIRE/ExPLOSION HAzARD
 WARNING! The cutting process can produce streams of sparks which are a potential source of
ignition especially when cutting metal.

DO NOT use the cut-off tool where there are flammable liquids, solids or gases.
 DO NOT allow cut-off tool sparks to make contact with the operator’s clothing or any other fabric
such as cleaning rags. Fabrics contaminated with inflammable materials such as petrol, oil, grease,
paint and solvents are a particular fire hazard.
 To reduce the risk of clothing catching fire the operator should wear wool or cotton outer garments
treated with a fire retardant in preference to man-made fibres.
Original Language Version SA2501 Issue: 1 - 14/05/13
INSTRUCTIONS FOR:
AIR CUT-OFF 75mm LONG REACH
MODEL No: SA2501
© Jack Sealey Limited 2013