beautypg.com

Fig.1 fig.2, Fig.3, Introduction 3. installation – Sealey SM354CE User Manual

Page 2

background image

DO NOT run the bandsaw with the blade in the raised position.

DO NOT use the bandsaw in areas where fumes from paint,

solvents, or flammable liquids pose a potential hazard. Keep

all flammable materials (including wipes or cleaning rags)

away from the saw, and dispose of according to local

regulations.

DO NOT leave the bandsaw running unattended. Turn power

switch ‘Off’ and do not leave area until the blade has come to

a complete stop.

DO NOT use whilst under the influence of drugs, alcohol or

other intoxicating medication.

DO NOT use the bandsaw with the blade guards or bow rear

protective cover removed.

DO NOT stand on the bandsaw.

DO NOT use damaged or deformed bandsaw blades.

DO NOT use the bandsaw in wet or damp locations.

DO NOT use the bandsaw if you are fatigued.

Turn the bandsaw

OFF before raising the blade.

Wear protective gloves when handling workpiece and saw

blades.

Always secure the workpiece in the vice.

Keep correct footing and balance at all times and wear

non-slip shoes with steel toe caps.

Position of safety labels (pictograms) on machine. Do not remove

labels. If they become illegible or damaged they must be replaced.

Fig.1

Fig.2

3.1 TRANSIT AND LIFTING

3.1.1 A fork lift truck will be required to unload the palletised bandsaw

and transport it to the installation area.

3.1.2 A suitably rated crane used together with chains and shackles

should be used to lift the machine onto the sheet metal stand

and also to lift the whole assembly into its intended position.

See lifting points B & C in Fig.2 above. Alternatively, slings can

be used under the vice either side of the central pivot. Great

care should be taken to keep the load level and to ensure that

the slings do not apply pressure to components that should not

be heavily stressed.

3.2 INSTALLATION AREA

3.2.1 Ensure that there is adequate free space around the machine

bearing in mind that it may be necessary to cut from long

lengths of steel stock that need to be fed over the roller

attached to the back of the machine and that the stock will

need to be supported along its length beyond the machine.

3.2.2 The surface on which the machine is to be mounted should

be flat and level and capable of supporting the weight of the

machine.

3.2.3 Ensure that the work area is adequately illuminated.

3.2.4 The machine should be located near a power supply point that

is equipped with an overload cut out and suitable earthing.

3.2.5 The installation area should be free from excessive humidity

and atmospheric agents that could ignite.

3.3 ASSEMBLY

3.3.1 Remove the outer packaging and dispose of it responsibly in

accordance with local authority regulations.

3.3.2

Sheetmetal base

3.3.3 Take one of the wider panels to use as the front panel

ensuring that the floor fixing bracket is on the left. This panel

has a returned flange along either vertical edge. Bolt an end

panel to each vertical flange using the Ø8mm bolts, nuts and

washers supplied as shown below. Complete the structure by

bolting the back panel into place as shown below in Fig.3.

3.3.4 Using a suitable crane, lower the machine bed onto the top

of the assembled stand. There is a central threaded insert in

Fig.3

Manufactured to comply with Safety of Machinery (Safety)

Regulations 1992 (and amendments) and fully CE approved. Saw

arms are fitted with hydraulic damping to prevent the arm being

dropped onto the workpiece and to ensure smooth cutting

performance. Bow swivels up to 60° angle allowing workpiece to

always sit in a central position. Coolant fluid system and main power

controls are switched on individual 24V/230V circuits for extra safety.

Features auto and manual shut off switches giving the user options

of control when in use. Heavy-duty single phase electric motor.

2.1. Specification

Capacity 60° round ...............................................................Ø70mm

Capacity 60° square ................................................................60mm

Capacity 45° round .............................................................Ø120mm

Capacity 45° square ..............................................................110mm

Capacity 0° round ...............................................................Ø170mm

Capacity 0° square ................................................................170mm

Capacity 0° rectangle ....................................................95 x 210mm

Blade Size .......................................................22.0 x 0.9 x 2110mm

Blade Speed ......................................................................80mtr/min

Motor Power ............................................................................ 900W

Coolant Pump Power ................................................................ 25W

Overall Size (W x D x H) ...............................1500 x 800 x 1620mm

Weight .....................................................................................170kg

Supply..............................................................................230V - 1ph

Original Language Version

SM354CE Issue: 3(SP) - 29/09/14

© Jack Sealey Limited

2. INTRODUCTION

3. INSTALLATION

This manual is related to the following products: