Sealey GDM1630FR - Manual (Page 2)

3
Refer to speed chart for recommended drilling speeds.
p WARNING! Always wear approved eye or face protection when operating this drill. Use a dust mask if dust is generated.
p
WARNING! DO NOT wear gloves when drilling.
3
Others in the workplace should be kept at a safe distance from the drill, especially when it is in operation.
3
Keep the work area as childproof as possible by using padlocks and master switches.
3
Keep drill bits clean and sharp for best and safest performance.
3
Remove ill fitting clothing. Remove ties, watches, rings and other loose jewellery and contain long hair.
3
Locate the drill in a suitable work area, keep area clean and tidy and free from unrelated materials. Ensure there is adequate lighting.
3
Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.
3 Avoid unintentional starting.
7
DO NOT use drill for a task it is not designed to perform.
7
DO NOT allow untrained persons to operate the drill.
7
DO NOT get the drill wet or use in damp or wet locations or areas where there is condensation.
7
DO NOT operate the drill if damaged.
7 DO NOT use drill in an area where paint fumes, solvents or flammable liquids pose a potential hazard. Keep flammable material away from
the drill when operating. Flammable waste, such as wipes or cleaning rags, must be placed in a closed metal container and disposed of
correctly.
7
DO NOT exceed the rated capacity of the drill.
7
DO NOT operate the drill if any parts are missing as this may cause failure and/or personal injury.
7
DO NOT leave the drill operating unattended.
7
DO NOT operate the drill when you are tired, under the influence of alcohol, drugs or intoxicating medication.
3
When not in use switch off the drill, remove plug from the power supply and do not leave until the tool has come to a complete stop.
3. TECHNICAL SPECIFICATIONS
2. DESCRIPTION
The GDM790BR (bench) and GDM1630FR (floor) radial drills are suitable for light industrial, agricultural and woodworking applications. These
5 speed drills are fitted with flip-up safety guards and “No Volt Release” switches, which prevent accidental restart after a mains power
interruption. The drill head is adjustable fore and aft to accommodate a large range of workpiece sizes and can be rotated to give angled
drilling. A rack and pinion feed shaft with preset depth control for repetitive work is also included. Work clamps are available for these drills,
contact your local Sealey dealer for information.
4. CONTENT
4.1. Content
Check parts against the list below. If any items are damaged or missing contact your supplier.
3
Head Assembly 3 Column with Flange 3 Rack & Rack Ring
3 Base 3 Table 3 Table Arm, Bracket and Worm Gear
3 Adjusting Handle (table) 3 Feed Handles and Knobs (3) 3 Pivoted Clamp Bolts (4 - GDM790BR, 5 - GDM1630FR)
3 Chuck and Key 3 Safety Guard 3 Bolts (4)
3 Hex. Keys (2) & Wedge 3 Belt 3 Locking Shoe
3 Coach Bolts & Wing Nuts
Model GDM790BR GDM1630FR
Chuck Size (mm) 16 16
Spindle Nose Taper MT2 MT2
Head Rotation 45-0-90° 45-0-90°
Head Travel (mm) 320 320
Spindle Travel (mm) 80 80
Number of Speeds 5 5
Speed range (rpm) 500 - 2450 500 - 2450
Chuck to Table - max. (mm) 223 708
Chuck to Base - max. (mm) 390 1230
Chuck to Column - min. (mm) 120 115
Working Table (mm) 310 310
Working Base (mm) 165 x 155 200 x 185
Overall Base (mm) 340 x 210 420 x 250
Column Diameter (mm) 60 71
Overall Height (mm) 790 1630
Voltage (AC) 230 230
Motor Range - No Load (W)
Motor Range - Under Load (W)
370
550
370
550
Weight (kg) 37 61
Original Language Version GDM790BR, GDM1630 Issue: 4 - 23/03/10