Sealey TS12CZ - Manual (Page 6)

8. MAINTENANCE
8.1 clean the saw regularly to remove dirt, dust and chippings using a brush and cloth.
8.2 clean plastic components with water and detergent, never use caustic or abrasive cleaners.
8.3 replace the table insert (part no.76) should it become worn or damaged
7.2. Rip cutting
 WARNING! The safety precautions stated at the beginning of this section must
be adhered to.
ripping is when a board or similar workpiece is held against the fence and cut along
the length. the fence is used to position and guide the workpiece during
cutting. the workpiece is laid flat on the saw table with one edge held tightly against
the fence. the riving knife will prevent the saw cut from closing and binding the blade.
Proceed as follows:
7.2.1 to rip cut, the sliding plate assembly is mounted onto the fence guide at the
front of the table and the fence is attached to it by slackening the two black
plastic knobs, sliding the fence onto the two M6 bolt heads, setting in position
and locking in place by tightening the two black plastic knobs.
7.2.2 set the width of cut and then clamp the fence assembly in place by pushing
the locking handle down. (fig.15).
7.2.3 Adjust the blade height to just exceed the thickness of the workpiece.
7.2.4 Ensure that the blade guard and its side plates are free to move as the workpiece
passes beneath them.
7.2.5 Before starting consider how you will handle the workpiece and the off-cut when
ripping is complete. Depending on the size and type of workpiece, off-cuts and
workpiece may remain on the table or fall to the floor. Ensure that the table
extension provided is fitted at the rear of the main saw table to prevent long
workpieces and off-cuts from falling. off-cuts that remain on the table must not be
touched until the blade has completely stopped.
7.2.6 Ripping a workpiece more than 120mm wide
a) Hold the workpiece firmly against the fence and the table, and turn the saw on.
b) Ensure you are not standing in line with the blade. Hold workpiece firmly with both hands, pushing it along fence and into blade
(fig. 15).
c) continue to gradually feed the workpiece past the saw blade keeping your hands away from the blade guard.
d) Move the workpiece completely past the saw blade.
e) once the cut is complete handle the workpiece and off-cut according to 7.2.5.
7.2.7 Workpiece less than 120mm but more than 30mm wide
use the push stick provided to feed workpiece forward.
7.2.8 Workpiece 30mm wide or less
When ripping stock 30mm or less, position the fence as for thin workpieces (see fig.Z) and use a push block.
7.3 On/Off switch
the saw has a no-volt load switch which automatically switches the power off in the case of a power interruption. the
saw will not then restart ‘automatically’ when the power supply is reinstated.
fig.15
fig.16
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT: no liability is accepted for incorrect use of this product.
WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
INFORMATION: for a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode.
01284 757500
01284 703534 [email protected]
Sole UK Distributor, Sealey Group,
Kempson Way, suffolk Business Park ,
Bury st. Edmunds, suffolk,
IP32 7Ar
www.sealey.co.uk
Web
email
Original Language Version ts12cZ.V2 Issue: 3 (1)- 23/08/13 © Jack sealey Limited
Environmental Protection.
recycle unwanted materials instead of disposing of them as
waste. All tools, accessories and packaging should be sorted,
taken to a recycle centre and disposed of in a manner which
is compatible with the environment.
WEEE Regulations.
Dispose of this product at the end of its working life in compliance
with the Eu Directive on Waste Electrical and Electronic Equipment.
When the product is no longer required, it must be disposed of in an
environmentally protective way. contact your local solid waste
authority for recycling information.