Sealey TS12CZ - Manual (Page 3)

4.2 Match leg 3 to the corresponding numbered label attached to the side of the main table (see fig.3.) use only sets of fixings at
positions 3A and 3B at this stage. the other two fixing points will be shared with the fence guides which are fitted later.
4.3 Mount the switch unit to leg 3 using two self tapping screws..
4.4 Attach leg 4 as shown in fig.4. use 3 sets of fixings at positions 4A, 4B & 4c at this stage.
4.5 Attach leg 5 as shown in fig.5 using 4 sets of fixings in positions 5A, 5B, 5c & 5D. Attach extractor hose guide to leg 5 at this
point, using an 8mm spanner (fig.5)
4.6 Attach leg 6 as shown in fig.6 using 2 sets of fixings at positions 6c & 6D. the other two fixing points will be shared with the table
extension which is fitted later.
4.7 Assemble a short leg strut between legs 3 & 4 and between legs 5 & 6 using a single set of fixings at each end of each strut
(see fig.2) Ensure that the broader flat surface of the struts will be facing upwards when the unit is turned the right way up.
4.8 Assemble a long leg strut between legs 3 & 5 and between legs 4 & 6 using a single set of fixings at each end of each
strut (see fig.2)
Ensure that the broader flat surface of the struts will be facing upwards when the unit is turned the right way up.
4.9 Where the struts overlap each other on the inside of each leg (four places) bolt them together with a single set of fixings.
(see ‘f’ in fig.2)
4.10 If required, extend the length of the table by bolting the table
extension to the end or sideof the main table as shown in fig.2 & 6.
the end extension is offset towards leg 6 and shares two of the leg
fixings. use 3 sets of fixings in positions 6A, 6B and at position
‘f’ as shown in fig.6.
4.11 If fitting extension to the side of the table, insert the squared
shoulders of the 2 domed bolts into the squared holes in the long
edge of the table. Match with the corresponding slots in the long
edge of the extension and secure.
4.12 Attach the appropriate pair of bracing struts (two different lengths are
supplied) between the outer edge of the extension and the adjacent
leg cross brace as shown in fig.2.
use a single set of fixings at each end of each strut.
4.13 Attach fence guide (97) to the front table edge between legs 3 & 4
using two brackets (98) and supplied screw fixings etc.
4.14 Attach the two blue support plates (62) to the long edge of the
table (fig.6a). Bolt the sliding guide (63) to the support plates.
4. ASSEMBLY
 WARNINg! ENSuRE THAT THE SAW IS
NOT CONNECTED TO THE MAINS POWER
bEfORE COMMENCINg ASSEMblY.
4.0. Fixings. Most of the saw is assembled using M6
nuts, bolts and washers. to tighten these fixings you
will need two 10mm spanners.
unless otherwise stated, where the text refers to
‘a set of fixings’ this will mean
- 1 M6 x 16mm hex headed bolt
- 1 M6 flat washer (diameter 18mm)
- 1 M6 lock nut
4.1. Saw stand.
the main saw stand will be assembled upside down on a suitable clean/flat surface. If necessary place some protective material
down first. Place the main table with the blade/motor box attached upside down on the surface (ensure that the blade is retracted fully
(see section 6.2)) so that there is room to fix the table extension to it. the corners of the table are labelled 3,4,5 & 6 and these
numbers will be matched to the corresponding numbers on the legs.
Motor . . . . . . . . . . . . . . . . . . . . . . . . . 2000W - 230V
speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2950rpm
saw Blade . . . . . . . . . . . . . . . . . Ø315 x Ø30 x 3mm
Max. Depth of 90° cut . . . . . . . . . . . . . . . . . . . 90mm
Max. Depth of 45° cut . . . . . . . . . . . . . . . . . . . 60mm
Main table . . . . . . . . . . . . . . . . . . . . . . 800 x 550mm
output table . . . . . . . . . . . . . . . . . . . . . 800 x 400mm
Dust Extraction Port . . . . . . . . . . . . . . . . . . . . Ø28mm
3. SPECIFICATION
3.1. Specification
leg 3
leg 4
leg 6
F
dust extraction
duct
leg strut
(long)
leg strut
(short)
leg 5
fig. 2
fig. 3 fig. 4 fig. 5
F
F
F
push
stick
hook
leg
leg
leg
Original Language Version
table extension
fig. 6
ts12cZ.V2 Issue: 3 (1)- 23/08/13 © Jack sealey Limited