Super Systems AC20 RS485 Modbus - Manual (Page 56)

Page 56/59
TITLE: MODBUS/J-BUS Protocol for SSi’s- AC20 ENG. 824E REV. 1
300 - Decimal number relative to primary control variable page 28
301 - Decimal number relative to main control output in engineering units
page 28
302 - Decimal number relative to secondary control output in eng. units page 28
347 - Code for enable configuration mode page 29
348 - Code for enable security code mode page 29
349 - Code for lock/unlock control parameters page 29
350 - Lock/unlock status group hidden page 29
351 - Lock/unlock status group 1 page 29
352 - Lock/unlock status group 2 page 29
353 - Lock/unlock status group 3 page 30
354 - Lock/unlock status group 4 page 30
355 - Lock/unlock status group 5 page 30
356 - Lock/unlock status group 6 page 30
357 - Lock/unlock status group 7 page 30
358 - Lock/unlock status group 8 page 30
359 - Lock/unlock status group 9 page 30
526 - Serial interface protocol ("S.L.Pr") page 23
527 - Serial link device address ("S.L.Ad") page 23
528 - Baud rate for serial link ("S.L.bd") page 23
529 - Byte format for serial link ("S.L.bF") page 23
1000 - Anti-reset windup ("ArU") page 20
1003 - Main control output low limit ("ñ.OLL") page 20
1004 - Main control output high limit ("ñ.OLH") page 20
1005 - Main control output max rate of rise ("ñ.rñP") page 20
1006 - Proportional cycle time on main control output ("ñC.CY") page 20
1007 - Secondary control output low limit ("S.OLL") page 20
1008 - Secondary control output high limit ("S.OLH") page 20
1009 - Secondary control output max rate of rise ("S.rñP")
page 20
1010 - Proportional cycle time on secondary control output ("SC.CY") page 20
1011 - Set point low limit ("rL") page 20
1012 - Set point high limit ("rH") page 20
1013 - Rate of change for positive set point variation ("Grd1") page 20
1014 - Rate of change for negative set point variation ("Grd2") page 20
1016 - External control of auto/man function ("E.Añ") page 20
1100 - Alarm 1 type ("A1.tP") page 21
1101 - Alarm 1 configuration ("A1.Cn") page 21
1102 - Alarm 1 action ("A1.Ac") page 21
1103 - Alarm 1 standby function ("A1.St") page 21
1104 - Alarm 2 type ("A2.tP") page 21
1105 - Alarm 2 configuration ("A2.Cn") page 21
1106 - Alarm 2 action ("A2.Ac") page 21
1107 - Alarm 2 standby function ("A2.St") page 21
1108 - Alarm 3 type ("A3.tP") page 22
1109 - Alarm 3 configuration ("A3.Cn") page 22
1110 - Alarm 3 action ("A3.Ac") page 22
1111 - Alarm 3 standby function ("A3.St") page 22
1200 - Min value of proportional band calculated by the smart algorithm (“Pb.Lo") page 25
1201 - Max value of proportional band calculated by the smart algorithm ("Pb.Hi") page 25
1202 - Min value of integral time value calculated by the smart algorithm ("ti.Lo") page 25
1203 - Max value of integral time value calculated by the smart algorithm ("ti.Hi")
page 25
1204 - Relative secondary output gain calculation by the smart algorithm ("rG.CL") page 25
1300 - Timer for burn-off (“t.bOF”) page 24
1301 - Timer for purge (“t.PrG”) page 24
1302 - Timer for automatic burn-off interval (“bF.tr”) page 24
1303 - Timer for probe test interval (“Pb.tr”) page 24
1304 - Time lasting to beginning of burn-off procedure (“bF.ñn”) page 24
1305 - Time lasting to beginning of probe test procedure (“Pb. ñn”) page 24