Skutch Electronics AS-80 - Manual (Page 8)

• Remote Programming
In this mode you can re-program the unit by
calling it from a remote location any where in
the world, via a touch tone telephone. The
ANSWER/NO ANSWER jumper must be in the
ANSWER position to gain access to the AS-80
over the telephone line. To access the unit call
the phone number that the AS-80 is connected
to. The AS-80 will answer the call on the ring as
specified by the RINGS UNTIL ANSWER
parameter in the SYSTEM SETUP INFO. If this
parameter is set to the SHARED LINE mode
(29), then you must call the line, wait for it to
ring two times, hang up, count to 5, then call
again.
Once the AS-80 answers the line it will
emit a single BEEP. At the end of the BEEP
enter the following security access code:
1234#
At this point the AS-80 will BEEP on and
off to indicated that you have gained access to
the unit. You MUST keep making Touch Tone
entries or the AS-80 will time out and
disconnect after approximately 50 seconds.
• Output Control
At this point you can either turn "ON" or
turn "OFF" channel 1 or channel 2 outputs.
When you turn an output "ON" it will only stay
on for the duration of time that is specified in
the SYSTEM SETUP INFO. If you do not wish
to make any changes in the output control press
# and the AS-80 will advance to PHONE
NUMBER ENTRY.
*1 = Turn "ON" Channel #1
*2 = Turn "ON" Channel #2
*#1 = Turn "OFF" Channel #1
*#2 = Turn "OFF" Channel #2
# = To Bypass
• Phone Number Entry
There are 4 alert phone numbers that can be
entered. Phone numbers 1 and 2 are for channel
1 and phone numbers 3 and 4 are for channel 2.
The AS-80 will BEEP one time indicating that
you are at the phone number 1 entry point. After
you enter the first phone number, press # and
the AS-80 will BEEP two times to indicate entry
number 2, and so on up to the 4th entry. A
phone number can be from 2 to 32 digits in
length. If you wish to erase a number simply
press 1#. If you wish to bypass an entry without
making any changes to it, press #. If you wish to
program a phone number to call a pager see the
CALLING A PAGER section for more details.
Enter phone number then press #. Repeat
for all 4 phone numbers.
1# = To Erase Number Completely
# = To Bypass without making any
changes.
• Special Codes for TONE dialing!
! *0x = Delay x=1-9 seconds
! *2 = Wait for 5 seconds of Silence before
continuing.
! *3 = Dial a STAR Touch Tone
! *4 = Dial a POUND Touch Tone
! *8 = Next Touch Tone will last 6 seconds
! *9 = No Announcement at end of dialing.
! Special Command Codes for Pulse
Dialing!
! ** = Switch to TONE dialing for the rest
of the phone number
! *x = Delay x=1-9 seconds
• System Setup Info
The SYSTEM SETUP INFO is a string of
11 digits that controls many different functions
on the AS-80. If you wish to make any changes
at all, you MUST enter all 11 digits. If you
should make a mistake during the entry, and you
have not entered all 11 digits yet, simply press #
and a dual tone error tone will sound. When the
error tone is finished you can re-enter the 11
digit SYSTEM SETUP INFO. Once you have
entered the 11 digit number the AS-80 will
continue to the ANNOUNCEMENT mode. The
following is a diagram showing the SYSTEM
SETUP INFO and a description of each
parameter.
• Description of Parameters
The following 8 parameters make up the 11
digit SYSTEM SETUP INFO. The default string is:
0 1 1 02 10 10 2 0