Olson Technology OTEB-CW-B - Manual (Page 39)

36
RS-232 Provisioner Commands
RS-232 Command Code Units Notes
Set Control Mode to APC SMPC - Sets the control mode of the unit to Power Control.
Set Control Mode to AGC SMGC - Sets the control mode of the unit to Gain Control.
Set Control mode to ACC SMCC - Sets the control mode of the unit Current Control.
Set Output Power Setpoint SOP dBm Sets the APC mode setpoint.
Set Gain Control Setpoint SGS dB Sets the AGC mode setpoint.
Set Current Control Setpoint SLC Amps Sets the ACC mode setpoint.
Set “Input Power Low” alarm level SPINLOW dBm Sets the threshold level for the “Input power Low” alarm. Overrides the
factory default setting.
Read Factory Default “Input Power Low”
Alarm Level. RFDPINLOW dBm Reads the factory default setting for the “Input Power Low” alarm level.
Restore access level to user mode. LOGOUT - Disables access to the provisioning commands.
Change the access pass code for the pro-
visioning commands. PASSCODE - Sets the new passcode. The passcode must be a 6 digit number.
Default Value is 999999
Restore all parameters to their factory
defaults. RESTORE -
Set Relay “Input Power Low” Alarm Status. SRAPINLOW See
Note Enables or disables activation of the relay for the alarm
0 Disables the alarm, 1 Enables the alarm.
Set Relay “Input Power High” Alarm Status. SRAPINHIGH See
Note Enables or disables activation of the relay for the alarm
0 Disables the alarm, 1 Enables the alarm.
Set Relay “Input Power Too High” Alarm
Status. SRAPINTOOHIGH See
Note
Enables or disables activation of the relay for the alarm
0 Disables the alarm, 1 Enables the alarm.
Set Relay “Output Power Low” Alarm
Status. SRAPOUTLOW See
Note
Enables or disables activation of the relay for the alarm
0 Disables the alarm, 1 Enables the alarm.
Set Relay “Output Power High” Alarm
Status. SRAPOUTHIGH See
Note
Enables or disables activation of the relay for the alarm
0 Disables the alarm, 1 Enables the alarm.
Set Relay “Output Power Too High” Alarm
Status. SRAPOUTTOOHIGH See
Note
Enables or disables activation of the relay for the alarm
0 Disables the alarm, 1 Enables the alarm.
Set Relay “Fan Failure: Alarm Status SRAFAN See
Note Enables or disables activation of the relay for the alarm
0 Disables the alarm, 1 Enables the alarm.
Set Laser “Ambient Temperature High”
Alarm Status. SRATEMP See
Note
Enables or disables activation of the relay for the alarm
0 Disables the alarm, 1 Enables the alarm.
Set Minimum Current Adjust when in ACC
Mode SACCNUDGEMIN Amps Sets the minimum current that can be adjusted from the front panel inter-
face using the minor adjust feature when the unit is in ACC mode. Over-
rides the factory setting.
Set Maximum Current Adjust when in ACC
Mode SACCNUDGEMAX Amps Sets the maximum current that can be adjusted from the front panel inter-
face using the minor adjust feature when the unit is in ACC mode. Over-
rides the factory setting.
Set Minimum Power Adjust when in APC
Mode SAPCNUDGEMIN dBm Sets the minimum output power that can be adjusted from the front panel
interface using the minor adjust feature when the unit is in APC mode.
Overrides the factory setting.
Set Maximum Power Adjust when in APC
Mode SAPCNUDGEMAX dBm Sets the maximum output power that can be adjusted from the front panel
interface using the minor adjust feature when the unit is in APC mode.
Overrides the factory setting.
Set Minimum Gain Adjust when in AGC
Mode SAGCNUDGEMIN dB Sets the minimum gain that can be adjusted from the front panel interface
using the minor adjust feature when the unit is in AGC mode. Overrides the
factory setting.
Set Maximum Gain Adjust when in AGC
Mode SAGCNUDGEMAX dB Sets the maximum gain that can be adjusted from the front panel interface
using the minor adjust feature when the unit is in AGC mode. Overrides the
factory setting.