Olson Technology OTEB-CW-B - Manual (Page 37)

34
RS-232 Interface Commands
RS-232 Command Code Units Notes
Read Model # RMDL - Returns the Model Number
Read Serial # RSN - Returns the Serial Number
Read date of manufacture RDATE - Returns the date of manufacture
Read Firmware Revision RREV Returns the revision level of the firmware.
Set the IP address SIP
Set the gateway address SGATE
Set the network mask SNET
Get the IP address GIP Type a space after the opcode & before hitting the Return or Enter key
Get the gateway address GGATE Type a space after the opcode & before hitting the Return or Enter key
Get the network mask GNET Type a space after the opcode & before hitting the Return or Enter key
Read control mode type RCM - Returns either “POWER”, “CURRENT” or “GAIN” for the control mode type
Read Measured Gain value RMG dB Returns “Gain = xx.x”
Read Gain setpoint value RGS dB Returns “Gset = xx.x”
Read Minimum Gain Setpoint RMINGAIN db Return the minimum gain that can be set in AGC mode “Gmin = xx.x”
Read Maximum Gain Setpoint RMAXGAIN db Returns the maximum gain that can be set in AGC mode, in the format
“Gmax = xx.x”
Read Total optical Output power ROP dBm Returns “Pout = xx.x”
Read Constant Output Power value RPS dBm Returns “Pset = xx.x”
Read Maximum Power Setpoint RMP dBm Returns “Pmax = xx.x”
Read Current Setpoint value RCS Amps Returns “Iset = x.xxx ”
Read Maximum Current Setpoint RMC Amps Returns “Imax = x.xxx”
Read pump laser current RLC Amps Returns “Imeas = x.xxx”
Read Ambient Temperature RAT Deg. C Returns ”Amp. = XX deg C”
Read Total optical Input power RIP dBm Returns “Pin = x.xx” NOTE: this value could be negative and/or have 2
digits containing 1 decimal point; i.e. –12, -2.2, 0.0, 3.5
Read Temperature Alarm Threshold RTEMPTHRESH Deg. C Returns “AMP. minor alarm = XX deg C” Which = the current minor alarm
value. major alarm temp > minor alarm temp
Read “Input Power Low” Alarm Level RPINLOW dBm Returns: “Pin Low Alarm Level = xx.x”
NOTE: this value could be negative and/or have 2 digits containing 1 deci-
mal point; i.e. –12, -2.2, 0.0, 3.5
Read “Input Power Off” Alarm Level RPINOFF dBm Returns: “Pin Off Alarm Level = xx.x”
NOTE: this value could be negative and/or have 2 digits containing 1 deci-
mal point; i.e. –12, -2.2, 0.0, 3.5
Read “Input Power High” Alarm Level RPINHIGH dBm Returns: “Pin High Alarm Level = xx.x” NOTE: this value could be negative
and/or have 2 digits containing 1 decimal point; i.e. –12, -2.2, 0.0, 3.5
Read “Input Power Too High” Alarm Level RPINTOOHIGH dBm Returns: “Pin Too High Alarm Level = xx.x NOTE: this value could be nega-
tive and/or have 2 digits containing 1 decimal point; i.e. –12, -2.2, 0.0, 3.5
Read “Output Power Low” Alarm Level RPOUTLOW dBm Returns the threshold level for the “Output Power Low” alarm, in the format
“Pout Low Alarm Level = xx.x”
Read “Output Power Off” Alarm level. RPOUTOFF dBm Returns the “Output Power Off” Alarm threshold, in the format “Pout Off
Alarm Level = xx.x”
Read the Autorestore Input Power Thresh-
old RAUTOTHRESH dBm Returns the threshold for the automatic restoration of emission, in the for-
mat “Autorestore Level = xx.x”
Enable Access to the provisioning com-
mands. LOGIN - This command must be followd by the 6 digit passcode to enable access to
the provisioning commands. Default Value is 999999
Read Status Value STA - Returns the status of the unit encoded as a 32 bit integer.
Bit 0 - Temperature Alarm
Bit 1 - Fan Alarm
Bit 2 - Output Too High Alarm
Bit 3 - Output High Alarm
Bit 4 - Output Low Alarm
Bit 5 - Input Too High Alarm
Bit 6 - Input High Alarm
Bit 7 - Input Low Alarm
Bit 8 - Output Off Alarm