Microsonic lcs-25/DD/QP - Manual (Page 3)

microsonic GmbH • Hauert 16 • D-44227 Dortmund • Tel: +49 2 31 / 97 51 51-0 • Fax: +49 2 31 / 97 51 51-51 • E-Mail: [email protected] • www.microsonic.de The content of this document is subject to technical changes. Specifications in this document are presented in a descriptive way only. They do not warrant any product features.
T1 + T2
T1 T2
T1 + T2
T1 + T2
T2 T1
Start here
T2 T1
T1 + T2
Ready
No function! No function! »F00«: no filter
»F01«: standard filter
»F02«: averaging filter
»F03«: foreground fil-
ter
»F04«: background
filter Defines the strength
of the chosen filter.
»P00«: weak filter up
to
»P09«: strong filter Minimum value: blind
zone
Maximum value: near-
window limit - 1
Low power mode Hysteresis
switched output D1
Measurement filter Filter strength Foreground
suppression Multiplex mode
device addressing
Multiplex highest
device address
Minimum value:
»001«
Maximum value: diffe-
rence between maxi-
mum range and de-
tect point - 1
During window mode
operation hysteresis
influences both detect
points. No function! Minimum value: sen-
sor-distant window
margin
Maximum value: 999
mm for lcs-25/... and
lcs-35/...,
999 cm for lcs-130/...
Measurement range Detection zone
sensitivity
T1 + T2
T1 T2
T1 + T2
T2 T1
T1 + T2
T1 T2
T1 + T2
T2 T1
T1 + T2
T1 T2
T1 + T2
T2 T1
T1 + T2
T1 T2
T1 + T2
T2 T1
T1 + T2
T1 T2
T1 + T2
T2 T1
T1 + T2
T1 T2
T1 + T2
T2 T1
T1 + T2
T1 T2
T1 + T2
T2 T1
T1 + T2
T1 T2
T1 + T2
T2 T1
Delay in seconds bet-
ween the detection of
an object and the out-
put of the measured
distance in case of ob-
ject approach (beha-
ves as on-delay).
"00": 0 s (no delay)
up to
"20": 20 s response
time
Response time Hysteresis
switched output D2
Minimum value:
»001«
Maximum value: diffe-
rence between maxi-
mum range and de-
tect point - 1
During window mode
operation hysteresis
influences both detect
points.
T1 + T2
T1 T2
T1 + T2
T2 T1
Setting of additional functions in the LCA-2
Note
Changes in the Add-on
menu may impair the sensor
function.
A6, A7, A8 , A10 , A11, A12
have influence on the respon-
se time of the sensor.
Press on the LCA-2 simultaneously for about 13 s until «Add» is shown in the LED-display. T1 T2 +
Affects the size of the
detection zone.
»E01«: high
»E02«: standard
»E03«: slight
T1 + T2
T1 T2
T1 + T2
T2 T1
T2 T1
T2 T2 T1
T1 + T2
Set detect distance in
mm or cm
For single detect
point press t»
until »- - -« is
displayed
Choose « » for NCC or
« » for NOC
T1 T2
For window mode
operation set far
detect point in
mm or cm
Press on the LCA-2 simultaneously for about 3 s until welcome message has passed
T2 T1
T1 + T2
T2 T1
T2 T1
T2 T2 T1
T1 + T2
Set detect distance in
mm or cm
Choose « » for NCC or
« » for NOC
T1 T2
T1 + T2
T2 T1
T1 + T2
T1 + T2
Set switched output D1 Set switched output D2
For single detect
point press t»
until »- - -« is
displayed For window mode
operation set far
detect point in
mm or cm
Ready
Start here
Optional setting of parameters using the LinkControl Adapter LCA-2 (Offline programming)
T1 + T2
T1
T1 + T2
T1 + T2
T1
T1 T2 +
Offline programming
Load Sensor parame-
ters in the LinkControl
Adapter LCA-2
Change parameters
and additional functi-
ons as described here
Write changed para-
meters back into the
lcs-sensor
Please refer to the quick refe-
rence guide on the LCA-2.