Comtech EF Data CRS-200 - Manual (Page 68)

Remote Control CRS-200 Redundancy Switch
B–8 Rev. 1
Parameter
Type
Command
(Instruction
Code and
qualifier)
Arguments for
Command or
Response to
Query
Description of arguments
(note that all arguments are ASCII numeric codes, that is,
ASCII codes between 48 and 57)
Response to Command
(target to controller)
Query
(Instruction Code
and qualifier)
Response to query
(target to
controller)
Restore
Holdoff
Time RSH= 2 bytes,
numerical Command or Query.
Sets or queries the restore holdoff delay time used when
auto mode prepares to return a previously faulted modem
back online due to another traffic modem’s failure:
02-99 = # of seconds after offline traffic modem lost its
fault before it is put back online so that redundant modem
can bridge the newly faulted modem RSH= (message ok)
RSH? (received ok,
but invalid arguments
found)
RSH * (message ok,
not permitted in current
mode RSH? RSH =xx
(same format as
command
arguments)
Modem
Alarm Mask MAM= 1 byte, numerical Command or Query.
Sets or queries the modem alarm mask:
0 = no faults masked but invalid arguments
1 = Tx faults masked
2 = Rx faults masked
3 = Both Tx and Rx faults masked MAM = (message ok)
MAM? (received ok,
found)
but not permitted in
current mode MAM? MAM =x
(same format as
command
arguments)
MAM * (message
ok,
Switch
Alarm Mask SAM= 1 byte, numerical Command or Query.
Sets or queries the modem alarm mask:
0 = no faults masked but invalid arguments
1 = PSU A faults masked
2 = PSU A faults masked SAM = (message ok)
SAM? (received ok,
found)
SAM * (message ok, but
not permitted in current
mode SAM? SAM =x
(same format as
command
arguments)
Audio Alarm
Mask AAM= 1 byte, numerical Command or Query.
Sets or queries the audio alarm mask:
0 = no faults masked (audio enabled in response to any
fault)
1 = Switch faults masked
2 = Modem faults masked
3 = All faults masked (audio never enabled) AAM = (message ok)
AAM? (received ok,
but invalid arguments
found)
AAM * (message ok,
but not permitted in
current mode AAM? AAM =x
(same format as
command
arguments)
Switch ID
string SID= 24 bytes, ASCII Command or Query.
Sets or queries the user-defined Switch ID string, which is
a fixed length of 24 characters.
Valid characters include:
Space ( ) * + - , . / 0-9 and A-Z. SID= (message ok)
SID? (received ok,
but invalid arguments
found) SID? SID=xxxxxxxx
xxxxxxxxxxxxx
xx (same format as
command
arguments)
Restore
Holdoff
Time RSH= 2 bytes,
numerical Command or Query.
Sets or queries the restore holdoff delay time used when
auto mode prepares to return a previously faulted modem
back online due to another traffic modem’s failure:
02-99 = # of seconds after offline traffic modem lost its
fault before it is put back online so that redundant modem
can bridge the newly faulted modem RSH= (message ok)
RSH? (received ok,
but invalid arguments
found)
RSH * (message ok, but
not permitted in current
mode RSH? RSH =xx
(same format as
command
arguments)
Modem
Alarm Mask MAM= 1 byte, numerical Command or Query.
Sets or queries the modem alarm mask:
0 = no faults masked
1 = Tx faults masked
2 = Rx faults masked
3 = Both Tx and Rx faults masked MAM = (message ok)
MAM? (received ok, but
invalid arguments found)
MAM * (message ok, but
not permitted in current
mode MAM? MAM =x
(same format as
command
arguments)