beautypg.com

Hardware specifications – NEXCOM VTC 1010 User Manual

Page 17

background image

Copyright © 2013 NEXCOM International Co., Ltd. All Rights Reserved.

3

Chapter 1: Product Introduction

VTC 1010 User Manual

Hardware Specifications

CPU

▪ Intel

®

Atom™ processor E3827, dual core 1.75GHz

Memory

▪ 1x 204-pin DDR3L SO-DIMM socket support 1066MHz / 1333MHz up to 8GB.

Default 2GB

Storage

▪ 1x 2.5” SATA 2.0

▪ 1x SD card socket

Expansion

▪ 1x full size Mini-PCIe socket (USB 2.0)

▪ 1x full size Mini-PCIe socket (USB 2.0 + PCIe)

▪ 1x full size Mini-PCIe socket (mSATA or PCIe)

▪ 1x half size Mini-PCIe socket (USB 2.0 + PCIe)

Function

▪ 1x default u-blox UBX-G6010 GPS module (50-channel and GALIELO) or

optional modules with dead reckoning or GLONASS support

▪ Built-in G-sensor, Gyroscope, and e-Compass sensors

I/O Interface-Front

▪ 8x LED for power, system status, storage, WWAN, WLAN, GPS, LAN, GPIO

▪ 2x external accessible SIM card socket (selectable) with cover

▪ 1x audio jack 3.5mm for WWAN voice communication, including 1x Mic-in and

1x Line-out

▪ 1x external accessible SD card socket with cover

▪ 1x event button (trigger type)

▪ 1x reset button

▪ 1x type A USB 3.0 compliant host, supporting system boot up.

I/O Interface-Rear

▪ 1x 9~36VDC input with ignition and 11W typical power consumption

▪ 1x type A USB 2.0 compliant host, supporting system boot up

▪ 1x RJ45 10/100/1000 Fast Ethernet with LED

▪ 1x phone jack 3.5mm for Mic-in (for WWAN voice communication)

▪ 1x phone jack 3.5mm for Line-out (for PC audio)

▪ 1x DB-15 VGA. Resolution up to 2500 x 1600 @60Hz

▪ 1x DP port. Resolution up to 2500 x 1600 @60Hz

▪ 1x DB-9 for RS-232

▪ 4x antenna hole for GPS/ WWAN/ WLAN/ BT

▪ 1x LHF 60-pin connector

1x 6-pin power connector, 12VDC output (max: 1A)
1x type A female USB 2.0 compliant host, supporting system boot up.
1x DB-9 RS-232
1x DB-9 RS-422/ 485
1x DB-9 female 3x DI and 3x DO. Onboard CAN 2.0B signals
(Programmable Digital Input)
Input Voltage (Internal Type): 5VDC TTL (default)
Input Voltage (Source Type): 3~12VDC
(Programmable Digital Output)
Digital Output (Sink Type): 5VDC TTL (default), max current: 20mA
Digital Output (Source Type): 3~24VDC, max current: 150mA
1x DB-9 for optional ODBII module (ASE J1939 or J1708)
1x DB-9 for optional GPS Dead Reckoning module
4x BNC connector video-in for optional 4-channel video capture card
4x audio connector for 7.1 channel audio output

(front, center/ woofer, rear surround, side surround)

Power Management

▪ Selectable boot-up & shut-down voltage for low power protection by

software