Specifications - hd 19t21 std-xxx-fxxx, Specifications – Hatteland Display 26 inch - HD 26T21 STD (Widescreen) User Manual
Page 63
63
IND100129-150
Specifications - HD 19T21 STD-xxx-Fxxx
SPECIFICATIONS
Note: All specifi cations are subject to change without prior notice!
Please visit www.hatteland-display.com for the latest electronic version.
2/2
• W:429.00 [16.89''] x H:382.00 [15.04''] x D:74.50 [2.93''] mm [inch]
• 4 x M6 VESA mounting 280x150mm, Max 12mm deep
• Weight: 7.8kg / 17.2lbs
• High Quality TFT with LED Backlight
• 19.0 inch viewable image size, Aspect Ratio 5:4
• TFT active-matrix liquid crystal panel
• MVA (Multi-domain Vertical Alignment) LCD Technology
• Native Resolution
: 1280 x 1024
• Pixel Pitch (RGB)
: 0.294 (H) x 0.294 (V) mm
• Response Time
: 20ms (typical), “black” to “white”
• Contrast Ratio
: 1000:1 (typical)
• Light Intensity
: 300 cd/m² (typical)
• Viewable Angle
: +/- 89 deg. (typical) (Up/Down/Left/Right)
• Active Display Area
: 376.32 (H) x 301.056 (V) mm
• Max Colors
: 16.7 million
Multi-power Supply:
• 115&230VAC - 50/60Hz + 24 VDC
- HD 19T21 STD-Mxx-Fxxx
Note: You may connect either AC power or DC power or both. In case both sources
are connected, power will be sourced from the AC input. If AC input is lost, there will
be a uninterrupted switch-over to DC input.
Power Consumption:
• Operating AC/DC Standard
: 33W (typ) - 125W (max)
A P P R O V A L S & C E R T I F I C A T E S
Physical Considerations:
TFT Technology:
TFT Characteristics:
Power Specifications:
This product have been tested / type approved by the following classification societies:
IEC 60945 4th (EN 60945:2002)
IACS E10
ClassNK - Nippon Kaiji Kyokai
GL - Germanischer Lloyd
DNV - Det Norske Veritas
ABS - American Bureau of Shipping
CCS - China Classification Society
BV - Bureau Veritas
LRS - Lloyd’s Register of Shipping
EU RO MR - Mutual Recognition
Compass Safe Distance: HD 19T21 STD-xxx-Fxxx
Standard: 125cm Steering: 75cm
• Digital separate synchronization
• Composite synchronization
• Synchronization on green
• Auto detects VGA -> SXGA, interlaced and non interlaced
• Video Signal
: Analog RGB 0,7Vp-p
: Input Impedance 75 Ohm
Synchronization Range:
• Horizontal
: 31.5 kHz to 91.1 kHz
• Vertical
: 60 Hz* to 85 Hz
* Recommended for optimal picture quality
Resolutions:
• VGA
: 640 x 480 (including 640 x 350)
• SVGA
: 800 x 600 (including 720 x 400)
• XGA
: 1024 x 768
• SXGA
: 1280 x 1024*
* Recommended for optimal picture quality
Synchronization:
Supported Signals:
• Operating
: Temperature -15 deg. C to +55 deg. C
- Humidity up to 95%
• Storage
: Temperature -20 deg. C to +60 deg. C
- Humidity up to 95%
• IP Rating
: Protection: IP66 front - IP22 rear (EN60529)
Lifetime Considerations:
Even although the test conditions for bridge units provide for a maximum
operating temperature of 55°C, continuous operation of all electronic
components should, if possible, take place at ambient temperatures of only
25°C. This is a necessary prerequisite for long life and low service costs.
Behind front bezel - Glass Display Control™ (GDC) IP66:
• Power On/Off, On Screen Display Menu, Brightness Control (-/+)
• Hotkeys (left/right), Mode Status Indicators (ECDIS, Service)
• Buzzer (not visible), Light Sensor (not visible)
• Projected Capacitive Touch Screen (Multitouch, USB interface)
• Optical Bonding Technology
• Color Calibrated models (ECDIS)
Environmental Considerations:
User Controls:
Factory Options:
• DVI-D Signal IN
: 1 x 24p DVI (female)
• RGB Signal IN
: 1 x 15p HD D-SUB (female)
• SCOM RS-422/485 : 1 x 5-pin Terminal Block 3.81, non-isolated+Buzzer
• SCOM RS-232
: 1 x 9p D-SUB (female) non-isolated
• If Touchscreen
: 1 x USB TYPE B Connector (female)
• AC Power IN
: 1 x Std IEC Inlet
• DC Power IN
: 1 x 2-pin Terminal Block 5.08
Signal Terminals:
For a full overview of typenumbers, please review the following link:
www.hatteland-display.com/pdflink/ind100780-3.php
• HD CMB SX1-A1
: 1 x Console Mount Kit (3-12mm). EN60945 Tested
• HD CMB SX1-A2
: 1 x Console Mount Kit (1-12.75mm). EN60945 Tested
• HD CMB SX1-A3
: 1 x Console Mount Kit (1-12.75mm). EN60945 Tested
Long screws for easier installation in tight spaces.
• HD TMB SX1-B1
: 1 x Table Mount Bracket. EN60945 Tested
• HD VED SX1-A1
: 1 x VESA Bracket, not EN60945 Tested
• JH 19TAP STD-C1 : 1 x Frame Adapter (19" Series 1 to Series X) retrofit
Please see user manual/datasheet for more information
Available Accessories: