Poulan 195 - Manual (Page 7)

3. THROTTLE HANDLE ASSEMBLY
a. Remove the rear screw ôom the trigger hous­
ing. Figure 4,
b. Slide the trig^r housing onto the ri^t ride of
the handlebar. Align screw holes in the trigger
housing with the sirew hole in the handlel^.
c. Reinstall the rear screw in the trigger housing.
Tighten securely.
NOTE; Make sure the engine switch is located on
the top side of the handle.
d. Secure the loose wire assembly in the groove in
the shaft pad.
Screw
Screw
Wire Assembly "
Hole
hi Shaft Pad
Figure 4
4. TRIMMER HEAD & PLASTIC SHIELD
AWABNING
The shield must be properly installed for all line
tiinuner usage* The shield provides partial pro-
tectionfrom the risk of thrown objects to the op­
erator and others and is equipped with a line
limiter which cuts excess line to proper length*
A WARNING
FEolure to install the shi^d in the position shown
in Figmre 5 can result in serious injury to the op­
erator. The length of the shield must be tdigned
with the length of the tube. Direct the widest
a. Remove and discard the packing cover from
the arbor shaft if so equipped.
CAUnONil The line limiter (on the underiside
of the shield) is sharp and can cut you*
b . Place the shield under the gear box and insert
four strews “B,” through the gear box into the
shield. Figure 5.
c. Tigfhten screws “B,” evenly and securely with a
standard screwdriver.
NOTE; Although a screwdriver slot is provided in
screws “B.**, it is easier to install the screws
with a wrench or socket.
Install grass washer "H.” over the arbor shaft.
Make sure grass washer “H." is against and
curved over the dust cup. Figure 6 .
Start threading the trimmer head onto the ar­
bor shaft as shown in Figure 5 .
Align the hole in the dust cup with the hole in
the center front of the gear box by turning the
trimmer head.
ir^ert the large hex wrench provided) into the
aligned holes to keep the arbor sb^ from
tuniing. Figure 6 (inset).
d.
e.
f.
g-
Gear Box
Clamp
Widest Part
of Shield
Toward
Engine
Screw B.
Dust Cup
Arbor Shaft
Grass
Trimmer
Head
Direction
to Install
Figure 5
h. Ti^ten the trimmer heid counterclockwise
a^imst gr^s washer “H.” and the dust cup
while holding the large hex wrench. See Fig­
ure 5 (inset),
i. Remove the hex wrench.
NOTE: To remove the trimmer head« insert
the hex wrench into the aligned holes in the dust
cup and gear box. Unthread the trimmer head. Be
sure to store the grass washer, plastic shield, 4
shield screws, and hardware with the trimmer
head for future use.
5. METAL SHIELD AND BLADE
A DANGER
The metal shield must be properly installed on
illtfi U>ol anytime the tool is used with the blade*
JTke forward tip on the metal shield helps to re­
duce the occurrence of blade thrust which can
cause serioris ir^ury such as amputation to the
operator or bystanders*
A DANGER
E^iire to install the shield in the position
i^pwn in Figures 6 and 7 can result in serious
ii]^j|iiry to the operator. The length of the shield
must be aligned with the length of the tube. Di-
rect widest part of the shield toward the engiTie.
NOTE: Ifyourunit is equipiffid as a line trimmer, re­
move the trimnier head, grass washer, andplastic
shield before installingme metal shield and blade.
Store parts for future use.
a. Reinove and discard the packing cover from
the arbor shaft, if so equipped.
b. Remove the dust cup,
c. Position the retention plate on the underside
of the metal shield and al^ screw holes. Make
sure the flat ride of the plate is against the met­
al shield Figure 6.
d. H
the metal shield under the gear box,
screwholes. Figured.
- 7 -