KEYENCE CV-X100 Series - Manual (Page 2)

2
The equipment and accessories listed below are included in the package
when shipped. After opening the carton, check that you have received all
of the equipment and accessories listed below.
Standard Package
• Controller Unit × 1
(CV-X100/X150/X170)
• SD Card
(OP-87133 (512MB): CV-X100/X150,
CA-SD1G (1GB): CV-X170) × 1
(pre-installed in SD1 slot)
• Dedicated mouse (OP-87506) × 1
• Software DVD-ROM for PC × 1
• Controller instruction manual × 1
General Cautions
General cautions for the controller
Operating environment and conditions
Measures to be taken when an abnormality occurs
Usage
Maintenance
CE Marking
KEYENCE evaluates compliance with the requirements of the EC
directive according to how products fulfill the below conditions. KEYENCE
has confirmed that this product meets these requirements. When this
product is used in EU nations, take note of the following precautions.
EMC Directive (2004/108/EC)
• Applicable standard EMI: EN61326-1, Class A
EMS: EN61326-1
• Use cables shorter than 30 m to connect the controller and its external
devices.
However, these precautions do not guarantee that the customer’s entire
machinery installation is compliant with the EMC Directive. The customer
is responsible for determining the compliance of the overall machinery
installation.
Package Contents
Safety Precautions
• Do not use this product for the purpose of protecting the
human body or any part thereof.
• Because this product was not designed for use in an
explosion-proof area, it must never be used in an explosion-
proof area.
• Before starting or operating the system, check to make sure
all system functions are working properly.
• If any Keyence product fails, take all safety precautions to
prevent damage before using the system again.
• If the system is operated beyond its published specifications
or if the system is modified, its functions and performance
cannot be guaranteed.
• Please note that when the system is used in combination
with other instruments, its functions and performance may
be degraded.
• Do not subject the controller or connected devices to a
sudden change in temperature.
There is the risk of condensation occurring.
• Do not use with any power voltage other than 24 VDC. Doing
so may cause fire, electric shock, or product malfunction.
• Do not disassemble or modify the unit. Doing so may cause
fire or electric shock.
• To use the system properly and safely, avoid installing this unit
in the following locations. Doing so may cause fire, electric
shock, or product malfunction.
– Locations that contain moisture or dust, or that are
poorly ventilated.
– Locations where the system is exposed to direct
sunlight or temperature increases.
– Locations where there are flammable or corrosive
gases.
– Locations where the unit may be directly subjected to
vibration or impact.
– Locations where water, oil or chemicals may splash
onto the unit.
– Locations where static electricity is present or electric
discharge may occur.
WARNING
CAUTION
NOTICE
CAUTION
CAUTION
• Keep this unit and cables away from high-tension cables and
power lines.
Otherwise, noise may cause malfunction or accidents.
• Bundle cables with spiral tubing material. Direct bundling will
concentrate the cable load on the bindings, which can result
in cable damage or short circuit.
• The controller and optional devices are precision
components. To maintain performance do not subject them
to vibration or shock.
In the following cases, turn the power OFF immediately. Using
the unit in an abnormal condition may cause fire, electric shock,
or product malfunction. Contact your local Keyence office for
repair.
• If water or debris enters the system
• If the system is dropped or the case is damaged
• If smoke or a burning smell emits from the controller
• Before making any connections/disconnections, be sure to
turn off the power of this unit and connected devices. Failure
to do so may result in a malfunction of the controller or
connected devices.
• Do not turn the power off while you are programming.
Otherwise, all or part of the program settings may be lost.
• Do not block the ventilation holes. Otherwise, the inside
temperature may rise and a malfunction may occur.
• Do not allow an excessive amount of sunlight or bright indoor
light to enter the camera for a long period of time. Doing so
may cause damage to the image capture surface inside the
camera.
• Do not clean with benzene, thinner, or alcohol. Doing so may
cause discoloration or deformation of the unit.
• If the unit has any dirt on it, wipe it off with a cloth moistened
with a mild detergent, then wipe with a dry cloth.
Precautions on Regulations and Standards
NOTICE
CAUTION
NOTICE
NOTICE