1. gamma correction (gamma), 2. auto knee on/off (auto knee), 3. total pedestal level control (total-ped) – Panasonic GP-US532H User Manual
Page 21: 4. chrominance level control (chroma gain), 5. detail band control (dtl band), 6. horizontal detail gain control (hdtl gain), 7. vertical detail gain control (vdtl gain), 8. red detail on/off (red dtl), 10. 2 dimentlon low pass filter (2d lpf), 11.6 chroma matrix controls
Attention! The text in this document has been recognized automatically. To view the original document, you can use the "Original mode".
8-1. Gamma Correction (GAMMA)
1. Move the cursor to GAMMA parameter. The “I” cur
sor starts blinking.
2. While observing the waveform monitor or the color
video monitor, adjust the gamma level.
If the "I" cursor is on the end of the side, the
gamma correction is set to OFF.
If the “I" cursor is on the end of the side, the
black strech (BLACK STRET) is set.
8-2. Auto Knee ON/OFF (AUTO KNEE)
1. Move the cursor to the AUTO KNEE parameter,
2. Select ON or OFF for the auto knee mode.
8-3. Total Pedestal Level Control (TOTAL-PED)
1. Move the cursor to the TOTAL-PED parameter. The
"I" cursor starts blinking.
2. While observing the waveform monitor or the color
video monitor, adjust the total pedestal level (black
level).
Move the "I" cursor to the “+" side to obtain the
brightness.
Move the “I" cursor to the side to obtain the
darkness.
8-4. Chrominance Level Control (CHROMA GAIN)
1, Move the cursor to CHROMA GAIN parameter. The
“I” cursor starts blinking.
2. While observing the waveform monitor or the color
video monitor, adjust the chroma level.
8-5. Detail Band Control (DTL BAND)
1. Move the cursor to the DTL BAND parameter. The
“I" cursor starts blinking.
2. While observing the color video monitor, adjust the
aperture level.
Move the “I" cursor to the side to obtain the
higher frequency.
Move the "I" cursor to the side to obtain the
lower fequency.
8-6. Horizontal Detail Gain Control (HDTL GAIN)
1. Move the cursor to the HDTL GAIN parameter. The
‘T’ cursor starts blinking,
2. While observing the color video monitor, adjust the
aperture level.
Move the "I" cursor to the
“ 4 "
side to obtain the
sharpness.
Move the “I" cursor to the side to obtain the
softness.
If the "I” cursor is on the end of the side, the
horizontal detail level is set to OFF.
8-7. Vertical Detail Gain Control (VDTL GAIN)
1. Move the cursor to the VDTL GAIN parameter. The
“I" cursor starts blinking.
2. While observing the color video monitor, adjust the
aperture level.
Move the "I” cursor to the
“ 4 "
side to obtain the
sharpness.
Move the “I" cursor to the side to obtain the
softness.
If the "I" cursor is on the end of the side, the
vertical detail level is set to OFF.
8-8. Red Detail ON/OFF (RED DTL)
1. Move the cursor to the RED DTL parameter.
2. Select ON or OFF for the RED DTL mode.
When ON is selected, the red detail is enhanced.
8-9. Clear Digital Noise Reduction Control
(CLEAN DNR)
1. Move the cursor to the CLEAN DNR parameter.
2. Select OFF, LOW or HI for the CLEAN DNR mode.
8-10. 2 Dimentlon Low Pass Filter (2D LPF)
1. Move the cursor to the 2D LPF parameter.
2. Select ON or OFF for the 2D LPF mode,
8-11.6 Chroma Matrix Controls
(MATRIX R-G)
(MATRIX R-B)
(MATRIX G-R)
(MATRIX G-B)
(MATRIX B-R)
(MATRIX B-G)
1. Move the cursor to the desired matrix item. The 'T'
cursor starts blinking.
2. While observing the vectorscope or the color video
monitor, adjust the matrix level.
8-12. Chroma Phase Control (HUE)
1. Move the cursor to the HUE parameter. The "I" cur
sor starts blinking,
2. While observing the vectorscope or the color video
monitor, adjust the chroma phase (hue).
To reset to the factory setting
Any of the above settings except AUTO KNEE, RED
DTL, CLEAN DNR and 2D LPF, can be reset to the fac
tory settings.
Move the cursor to the desired item and press ^ and
► simultaneously for a second and more.
-
19
-