Panasonic KX-P3124 User Manual
Kx-p3124, Operating instructions, Quiet
Table of contents
Document Outline
- Panasonic
- KX-P3124
- Features
- Operating Environment
- Assembling the parts
- EZ set operator panel
- 16-Character Liquid Crystal Display (LCD)
- LOAD/PARK(*) Switch
- SUPER QUIET (^) Switch
- TOF SET (^) Switch
- TEAR OFF (♦) Switch
- ON LINE/FUNCTION Indicator
- POWER/PAPER OUT Indicator
- FF (PITCH) Switch
- LF (SET) Switch
- FUNCTION Switch
- Printhead gap lever
- Paper teed selector (o^ P. 23)
- Attach one end of the parallel interface cable to your printer as shown, and the other end to your computer.
- If the cable has a frame ground wire, connect it to the frame ground terminal.
- Plug printer into a grounded 3 prong AC socket.
- Installing the Ribbon Cassette
- Removing the Ribbon Cassette
- Fanfold Paper; Push Tractor Mode—Rear Feed
- Fanfold Paper: Pull Tractor Mode—Bottom/Front Feed
- O Unlock the tractors by pulling the tractor clamping levers forward.
- 0 Slide the tractors to accommodate the approximate width of the paper being used.
- Raise the upper tractor covers (A) only.
- Remove the pull up roller unit as shown.
- O Replace the top cover to its original position.
- 0 Close the smoked plastic cover.
- If ON LINE indicator is not lit, press [ON LINE) to get ready to print.
- Single Sheets and Envelopes: Friction Mode—Top Feed
- Single Sheets and Envelopes: Friction Mode—Front Feed
- O Turn the power switch on.
- 0 Adjust the printhead gap lever for the thickness of paper you are using.
- Set the paper feed selector to the position.
- O Open the paper door.
- 0 Insert one sheet of paper along the front paper guide until you feel resistance.
- If ON LINE indicator is not lit, press (ON LINE) to get ready to print.
- Characters Alignment
- Tear Off (Rear feeding only)
- Paper Parking (Rear feeding only)
- Top of Form Function
- Operation
- Setting the Function Mode Items
- Direct Access to FONT and PITCH Setting
- Setting POINT SIZE
- Press [FUNCTION] to enter the Function mode.
- Press (3 once to select “PRINT STYLE”.
- Press (2 to enter the Sub-menu.
- Press to enter the font selection menu.
- Press (3 or El to select the desired SC font (ex; COURIER-SC).
- Press (lQ (SET) to set the selection.
- Press to enter the font selection menu.
- Press @ or ® to select the desired point size.
- Press [L0 (SET) to set the selection.
- o
- PRINT SETTING Menu
- PRINT STYLE Menu
- EMULATION Menu
- PAGE FORMAT Menu
- PRINT MODE Menu
- TEXT ENHANCEMENT Menu
- Double High
- CMiOg iiii© ©saiq») (1)^
- ll(öm(D ßllsxas
- Character Set Selection
- Bit Image (Graphics) Mode Selection
- Bit Image (Graphics) Mode Selection
- Paper Feed Selection
- Page Format Selection
- Tabulation—Horizontal
- Tabulation—Vertical
- Carriage Control
- Data Control
- Download Character Selection
- Miscellaneous
- Color Selection
- Font Selection
- Character Pitch Selection
- Character Highlight Selection
- Character Highlight Selection
- Character Set Selection
- Bit Image (Graphics) Mode Selection
- Bit Image (Graphics) Mode Selection
- Paper Feed Selection
- Page Format Selection
- Tabulation—Horizontal
- Tabulation—Vertical
- Carriage Control
- Data Control
- Download Character Selection
- Miscellaneous
- o
- Color Selection
- Fanfold Paper
- Single Sheet
- Envelope
- Printing Area
- Parallel Interfacing
- Specifications:
- Connector pin signals
- Clear Buffer Function
- To enter the Hex Dump mode:
- To release the Hex Dump mode:
- Epson Italic Character Set (US)
- Epson Graphic Character Set 2
- Epson Character Set 2 (Multilingual)
- Epson Character Set 2 (Portugal)
- Epson Character Set 2 (Canada-French)
- Epson Character Set 2 (Turkey)
- IBM All Character Chart
- IBM Character Set 2 (Multilingual)
- IBM All Character Chart(Multilingual)
- IBM Character Set 2 (Portugal)
- IBM All Character (Portugal)
- IBM Character Set 2 (Canada-French)
- IBM All Character (Canada-French)
- IBM Character Set 2 (Norway)
- IBM All Character (Norway)
- IBM Character Set 2 (Turkey)
- IBM All Character Set (Turkey)
- Qjiiaiasaa? ©sG
- @D®e@a3^