Panasonic OMNIVISION PV-DM2799 - Manual (Page 52)

DVD Initial settings (continued)
Selecting DIGITAL AUDIO OUTPUT
Select the digital output to be output from the optical / coaxial
digital audio output connector of the unit.
1
Do steps 1 and 2 on page 51.
2
DISC LANGUAGES
STILL MODE
TV MODE
I ELD
Lettori»*
SE LECT : * ▼ SET : SET
END : ACTION
Display DIGITAL
AUDIO OUTPUT screen.
1) Press AT
to select.
2) Press
SET.
3
DIGITAL AUDIO OUTPUT
isssipiKaa
DolByDigTlal
(ils :OFF
Dynamic Range Compraaaion: OFF
V. S S. : VSS 2
SE LECT : a ♦ SET : SET
END : ACTION
Select the desired
item.
1) Press
AT
to select.
2) Press SET
repeatedly
for output.
“LPCM (DVD)” selections
OFF: Only linear PCM of 48 kHz/16 bit is output. When
playing DVDs recorded in linear PCM of 48 kH2/20 bit or
96 kHz, no digital audio is output. (Factory preset)
PCM: When playing DVDs recorded in linear PCM of 48 kHz/
20 bit/24 bit or 96 kHz, digital audio converted to 48
kHz/16 bit is output.
(Digital output of PCM audio is restricted to 43 kHz/16
bit or below for copyright protection.)
"Dolby Digital” selections
Bitstream: Dolby Digital (AC-3) bitstream (2ch-5.1ch) is output.
(Factory preset)
PCM: PCM (2ch) of 48 kHz/16 bit is output.
“dts” seiections
OFF: No output.(Factory preset)
Bitstream: dts bitstream is output.
“Dynamic Range Compression” seiections
OFF: Normal audio range is selected. (Factory preset)
ON: For dynamic sound even at low volume, this is useful for
late-night listening. [Dolby Digital (AC-3) DVDs only].
“V.S.S.” seiections
Virtual Surround Sound creates the effect of sound coming from
nonexistent rear speakers even when only connected to a
2-channel stereo system. [Dolby Digital (AC-3) DVDs only],
OFF:
No Virtual Surround Sound effect. (Factory preset)
VSS 1: Natural effect.
VSS 2: Emphasized effect.
Redisplay DVD menu
to continue setup.
Press ACTION and go
to step 2 to setup
another setting.
Or, to exit, press
ACTION three times.
4
ACTION
AT
Type of amplifier
to be connected
Recommendable setting
LPCM
(DVD) Dolby
Digital
dts
No amplifier is connected OFF Bitstream OFF
AV amplifier (with digital
audio input connector)
without Dolby Digital/dts
decoder
PCM*1 PCM*2 OFF-2
AV amplifier including
Dolby Digital decoder
PCM*^ Bitstream OFF
AV amplifier including
Dolby Digital/dts decoderPCM*’ Bitstream
•3
Bitstream
• Make settings according to amplifier connected to optical/
coaxial audio output as shown in above table.
• When a dts decoder is not connected, to enjoy dts DVD,
please select audio output other than dts at the dts DVD
menu screen. Otherwise, there will be no sound from the
unit speakers.
.1
.3
Audio output from unit is converted to 48 kHz/16
bit in addition to audio from digital audio output.
To enjoy high quality sound at 48 kHz/20 bit /24
bit or 96 kHz, connect the amplifier or decoder
directly to the audio output connectors, not to the digital
audio output connector. [Select “OFF' at the “LPCM (DVD)".j
When connecting an amplifier (with an optical/
coaxial digital input connector) which does not
contain the Dolby Digital (AC-3) or dts decoder,
be sure to select "PCM" or “OfT.
If “Bitstream" is selected, starting DVD play may cause
such a high level of noise as to be harmful
to your ears and damage the speakers.
When a dts decoder is connected, please select
"Bitstream" in "dts". If "OFF" is selected, there will be no
sound.
52
■ The virtual surround effect may not work properly for some
DVD software.
‘ Turn off other surround effects when using this virtual
surround effect.
’ For optimum effect, the distance between the unit and the
listener should be about 3 or 4 times the distance between
the right and left front speakers.
For assistance, call 1-800-211-PANA(7262)