Panasonic NV-F70EA - Manual (Page 15)

Setting the Clock to the Present Time Using the Bar
Codes
9 ?
i
H IMI ■ III
0
Hli a ñu t □ IG nun m IM n IM a W
m nil II M t □ 1 » □ MM m lili a Hit a IM
s) nil ■ M f □ 11111 ID MM a IHI a MI a nw
n M ■ Ml 1 □ IG amt G Hl m
m
a ilU
ID N1 ■ im IG MÜ ID latii a im a M a m
(U M I nil (Hi 1 □ MM a im ■ iin a M
n iHi am n □ anil «D IWi G nm a Wil a Hii
m fill ■ m *□ mill • □ linn a W ■ w a N11
■ nil ■ m *□ mil *'□ IMIII a m a NN a W
mm a nil »□ Mi MUM a MI a iiil a in
n m B mi »□ 1 ■1 •D ItM a Hll B Hll B Hl
a III a Hll mill *D IIM a MI a H a MI
a Ml am ■Hilt «□ anil a m a UN a UN
[■■Han □ 1 G aiiii ■ m a m a flN
_____ i in G 1 G HIM a lili a Hll B lUI
□ iim G MW a ini a NU B W
,
a
1
imp G Iim B ill D Ni a M
a ill □ mui G IIHII ■ in ■ Hll a in
l a nil □ nil □ 1■w D Hill a lin a Wl B lili
......
irn^m'
Ü 1 n Hi
m
lili ■ lili
a IIW □ im □ IIW D IIM
a nil □ anil D IWI Q W □ M G NU
a nil □ in' □ Hint □ IHIII
a nil □ 1 Hill □ null
□ lili
mD
III
mn
III Q III
mn
III «□ III (ü III
MD III III m IIH
»□ III MD IIM D III
MD III MD III m IIM
mn
IIH MQ Hi m IIM
MD HU
mn
lli D HI
«□
mi
MD
HI
H) IIH
mn
Hi MD III 01 IIH
MD HI MD nil n Hi
mu
mi MD III B III
mn
III m ill
Preparation
•Slide down the Mode Selector Cover on the Remote
Controller so that the Bar Code Reader Display can be
seen.
•Press the Digital Scanner On/Off Button to turn it “ON”.
O Trace the bar code “SETTING OF THE CLOCK".
SETTING OF THE CLOCK
□-
Trace the bar code for the year (YEAR).
o Trace the bar code for the month (MONTH).
Q Trace the bar code for the day of the month (DATE).
0 Trace the bar code for the hour (START TIME).
fOo ©START TIME
3 00 9 □-
0 Trace the bar code for the minute (MIN).
0 Press the Transmit Button on the Remote Controller
and then confirm that the time is displayed in the
Multi-Function Display of the VTR.
“ Beep-beep-beep-beep-
beep...’’ sound indicates that
the time setting is completed.
0 Press the Digital Scanner On/Off Button to turn it
“OFF”.
• If the transmission was not received correctly, the
“Beep-Beep, Beep-Beep” sound from the VTR will warn
you. In this case, perform transmission again.
• If the Remote Controller is left with no operation per­
formed for more than 4 minutes, it will automatically
switch over to the power-saving standby condition and the
lamp in the reading tip goes out. (In this case, bar codes
that have already been read (but not yet transmitted to the
VTR) will be cancelled.
•The bar codes “SETTING OF THE CLOCK”. “YEAR” and
“MONTH" are located on page 3 of the Programming
Sheet.
15