Panasonic WJ-SQ508 User Manual

Page 6

Attention! The text in this document has been recognized automatically. To view the original document, you can use the "Original mode".

20. Program Switch (PROGRAM)

This switch is a push - push type switch with LED

indicator. While the LED of this switch is on, the
programmed sequential switching which has been

previously set will be performed. To cancel the

programmed sequential mode, press this switch and

turn the LED off.

. Video Input Connectors (VIDEO IN 1/2- -/

)

These connector accept either FM (audio) mixed video

signals or standard video signals.

22. Alarm/ Sequence Video Output Connector

(ALARM/SEQ VIDEO OUT)

The standard composite video signal is provided at this
connector. When the WJ-SQ508 is in the sequential

mode, either the normal sequence or programmed

sequence, the sequential video signal is provided at this

connector. When the WJ-SQ508 is in the alarm mode,
the alarmed video signal is provided at this connector.

Note:

A Time Lapse VTR is recommended for use with

this connector.

23. Spot/Sequence Video Output Connector

(SPOT/SEQ VIDEO OUT)
The FM (audio) mixed video signal is provided at this
connector. When the WJ-SQ508 is in the sequential
mode, either the normal sequence or the programmed
sequence, the FM (audio) mixed sequential video signal
is provided at this connector. When the WJ-SQ508 is

in the spot mode, the FM (audio) mixed spot video signal
is provided at this connector.

Note:

An audio beat noise will be seen on the video

monitor when the FM (audio) mixed video signal

supplied

from

this

connector.

Turn

the

Spot/Sequence Audio Switch (26) to the OFF
position to eliminate the audio beat noise.

The video input of WV-CU300 accepts the

(audio)

mixed

video

signal

from

the

Spot/Sequence Video Output Connector (23) of
the WJ-SQ508 without audio beat noise.

24. Spot/Sequence Video Slave Input Connector

(SPOT/SEQ VIDEO SLAVE IN)

This

connector

accepts

the

(audio)

mixed

video signal from the Spot/Sequence Video Output

Connector (23) of another WJ-SQ508 in a master-slave

operation.

25. Alarm/Sequence Video Slave Input Connector

(ALARM/SEQ VIDEO SLAVE IN)
This connector accepts the video signal from the

Alarm/Sequence

Video

Output

Connector

(22)

another WJ-SQ508 in a master- slave operation

26. Spot/Sequence Audio Switch

(SPOT/SEQ AUDIO ON/OFF)
The audio signal on the spot/sequence video output

signal will be cut off when this switch is in OFF position.

If the audio sound is not necessary during a sequential

operation with a WV-CU300, turn this switch off. When

this switch is in ON position, the sequential switching

audio signal as well as the video signal will be obtained
at the WV-CU300.

27. Master/Slave Switch (MASTER/SLAVE)

This switch should be properly set when using the

master- slave operation of the WJ-SQ508. Turn this

switch to the MASTER position when this WJ-SQ508
is used as the master unit and turn this switch to the
SLAVE position on all the others WJ-SQ508 that are
used as slave units.

Note:

Turn this switch to the Master position when this
unit is used alone.

28. Data Input /Output Connector (DATA IN/OUT

/2)

The control data transmitted from other system

components (WV-CU300, WJ-MP404 or WJ-SQ508)

is supplied to one of these connectors. If the control

data has to be sent to other system components, use
the other connector for it.

Note:

(

) This connector is terminated by 750 automatically

when the BNC cable is connected.

(2) the data line should originate from WJ-MP404.

(Data Clock Switch to SND position) and should

loop through all necessary units. For additional

details see the WV-CU300 or WJ-MP404

operating instructions.

29. Station Number Selection Switch

(STATION NO. 1/2/3)

this switch is used to identify the station number of

each WJ-SQ508 in the system which branches out
from a WV-CU300.

Note:

Refer to the setting up of the station number on

page

30. Unit Number Selection Switch (UNIT NO.

}

This switch is used to identify the unit number of each
WJ-SQ508 in the system which branches out from a

WV-CU300.

Note:

The NO. 0 and NO. 9 on this switch are of no use.

Refer to the setting up of the unit number on page

31. External Timing Output Connector

(EXT TIMING OUT)

The sequential switching interval of WJ-SQ508 can be
externally controlled by a Time Lapse VTR The timing

pulse from the External Timing Input Connector (32) is

provided to this connector for another WJ-SQ508.

Note:

When the Time Lapse VTR is not used with this

unit, the timing pulse set by the Dwell Time Control
(5) is provided to this connector.