La-Z-Boy La-Z-Touch Massage System prior to 10/18/2010 - Manual (Page 10)

La-Z-Touch ® 10-Motor Massage & Heat Recliner
Programming Instr uctions:
The program feature provides the a bility to program the intensity levels of the
vibrating massage motor s in each zone.
To Use The Program Feature
1. Press PRGM to activate the feature (the light will star t blinking).
2. Press ZONE 1, Upper Back, and set the intensity level desired.
• Press + intensity to increase the intensity level
• Press - intensity to decrease the intensity level
3. Press ZONE 2, Lower Back, and set the intensity level desired.
4. Press ZONE 3, Hip Region, and set the intensity level desired.
5. Press ZONE 4, Upper Thigh, and set the intensity level desired.
6. Press ZONE 5, Lower Thigh, and set the intensity level desired.
7. Press PRGM to use the set intensity program that you just selected, w hich can
be used with any ZONES selected and in any mode--PULSE, WAVE and CIRCLE
(the light will now remain steady).
8. Press PRGM again to deactivate the set intensity program mode and retur n
to the default settings (the light will go off).
Your program remains in memor y until you set a new program. To activate the
set program ag ain
1. Press PRGM to activate the feature (the light will star t blinking).
2. Press PRGM again to use the last programmed setting (the light will now
remain steady).
3. Press PRGM again to deactivate the feature and retur n to the default settings
(the light will tur n off).
NOTE: The program may be reset to the default settings when a disruption in
the power supply occurs, such as an electrical power outage, and you will
need to reset the program to your desired settings.
Customize the reclining action of your Reclina-Rocker ® or Reclina-Way ® Chair.
-- Risk of injur y.
• This unit is equipped with a tension adjustment feature for the reclining
mechanism that is preset at the factory. The tension setting can be changed for
your personal preference. To avoid tipover and assure stability, do not operate
the unit with the tension adjustment wing nuts completely loosened (see
Adjustment Instructions).
NOTICE:
Risk of damage.
• Make sure the legrest on each unit is closed before tilting forward and
adjusting the tension.
• Do not completely tighten the wing nuts, as damage will occur. The tension
spr ings should not be completely compressed after making adjustments .
If this occur s , the wing nuts must be loosened counterclockwise a
minimum of 1 ⁄ 2 -tur n to avoid damage to the spr ing tension assembly.
• Do not completely loosen the wing nuts. The spring should not slide on the bolt
after making adjustments. If the spring slides on the bolt, tighten the wing nut
clockwise a minimum of 1 ⁄ 2 -turn, after the spring no longer slides on the bolt.
• Adjust bot h wing nuts equally.
Reclining Tension Adjustment Instr uctions
You can adjust the tension of the reclining mechanism to respond to your
individual size.
1. Gently tilt the reclining chair forward to rest on its ar ms and top of the back.
Locate the wing nuts , one on each side, toward the back of the recliner
under each reclining seat (F I G U R E 1; only one side shown).
2. Adjust the tension by tur ning the wing nuts in 1 ⁄ 4 -tur n increments until the desired
setting is reached.
• A taller or heavier per son may choose to increase the reclining tension
by tightening the wing nuts clockwise.
• A smaller per son may choose to decrease the reclining tension by
loosening the wing nuts counterclockwise.
3. Retur n the reclining chair to the upr ight position. Test the new setting.
Make additional adjustments if needed following these steps .
Reclining Tension Adjustment
Instr uctions:
Tension Spr ing
Wing Nut
F I G U R E 1
19 18
WARNING