Sony SPP-1000 User Manual
Cordless telephone
This manual is related to the following products:
Table of contents
Document Outline
- Cordless Telephone
- Operating Instructions.
- Owner's Record
- IMPORTANT SAFETY INSTRUCTIONS
- INFORMATION FOR GENERAL TELEPHONES
- Checking the package contents
- Table of Contents
- Identifying the parts
- Placing the phone units
- Choosing the best location for the base unit
- Connecting the base unit
- Hanging the base unit on a wall
- Charging the battery pack
- Choosing tone or pulse dialing
- Setting the dial mode
- Using touch-tone services with pulse dialing system
- Turning the ringer on or off
- Setting the digital security code
- Making and receiving caiis
- Making calls
- Receiving calls
- 1 Pick up the cordless handset from the base unit.
- 2 Press TALK, and wait until the TALK lamp lights.
- 3 Dial the phone number.
- 4 When you finish talking, press OFF or replace the cordless handset on the base unit.
- 1 When you hear the phone ring, pick up the cordless handset from the base unit.
- 2 When you finish talking, press OFF, or replace the cordless handset on the base unit.
- Redialing
- If interference occurs on the cordless handset
- Operating the phone during caiis
- Paging the cordless handset (spp-ioio oniy>
- Memory dialing
- recautions
- On power source
- On installation
- On maintenance
- Troubleshooting
- Registro del propietario
- IMPORTANTES INSTRUCCIONES DE SEGURIDAD
- GUARDE ESTAS INSTRUCCIONES
- INFORMACIÓN GENERAL SOBRE LOS TELÉFONOS
- Comprobación del contenido del paquete
- Indice
- Identificación de componentes
- 9
- 10 11
- 12
- 13
- 14
- 15
- 16
- 17
- 1 Botones TALK
- 2 Indicadores de pilas
- 3 Indicador TALK
- 4 Teclas numéricas
- 5 Botón REDIAL/PAUSE
- 7 Botones ONE-TOUCH DIAL (A.B.C)
- 8 Micrófono
- 9 Altavoz
- 10 Botón OFF
- 11 Botón FLASH
- 12 Interruptor RING ON/BATT SAVE
- 13 Compartimiento de pilas
- 14 Botón MUTE
- 15 Botón CHANNEL
- 16 Botón SPEED DIAL
- 17 Terminales de carga
- Colocación de las unidades telefónicas
- Selección de la mejor ubicación para la unidad base
- Conexión de la unidad base
- Conecte un extremo del adaptador de corriente CA (suministrado) a la toma DCIN 9V y el otro extremo a un tomacorrientes CA.
- 2 Enchufe un extremo del cable de línea telefónica largo (suministrado) en la toma TEL UNE y el otro extremo a la toma del teléfono.
- 3 Saque la antena completamente.
- Nota sobre el adaptador de corriente CA
- Colocación de la unidad base en la pared
- Lji>s
- Carga del bloque de pilas
- Se(ección de marcación por tonos o impulsos
- Ajuste del código de seguridad digital
- y recepción de llamadas
- utilización del teléfono durante llamadas
- Marcación en memoria
- Almacenamiento de números de teléfono en memoria
- 1 Presione PGM.
- 2 Para realizar una marcación de una sola pulsación:
- Presione uno de los tres botones ONE-TOUCH DIAL (A-O.
- Para realizar una marcación rápida:
- 1 Presione SPEED DIAL.
- 2 Presione una tecla entre 1 y 7.
- 3 Marque el número de teléfono que desee almacenar.
- 4 Presione PGM.
- Nota sobre el almacenamiento de números—
- Para cambiar un número almacenado
- Marcación en memoria
- Realización de llamadas a números en memoria
- Precauciones
- Solución de problemas
- Especificaciones
- Almacenamiento de números de teléfono en memoria