Taylor-Wharton KRYOS Controller - Manual (Page 20)

18
KRYOS
Menu Access causes the control to make some decisions on logging an event and
they are handled in the following manner: Temperature is immediately logged (if it
is enabled) and then a fresh time period is started when the Menu system is exited.
System and error logs are placed in a suspended state until the control exits the
menu system and timing is started again. Duration of system and error logs then are
total time of the event less any time that the user was in the menu system.
When logs are dumped to the serial port, the oldest events are sent first. The control
operates on the FIFO (First In First Out) method. If the maximum number of entries
is reached, the oldest are lost to make way for the newest entries.
Dump Logs
DUMP SYSTEM LOGS is accessible through the menu system of the control
(
MENU, 4, 1, 1). This option sends data from the system logs out the serial port
of the freezer. When this option is chosen, the display reports how many system
logs are stored. While the data is being sent to the serial port, it can be paused or
completely cancelled through the menu system.
DUMP ERROR LOGS is accessible through the menu system of the control
(
MENU, 4, 1, 2). This option sends data from the error logs to the serial port of the
freezer. When this option is chosen, the display reports how many error logs are
in the system. While the data is being sent out the serial port, it can be paused or
completely cancelled through the menu system.
DUMP TEMP LOG #1 and TEMP LOG #2 are accessible through the menu system
of the control (
MENU, 4, 1, 3 or MENU, 4, 1, 4). This option sends data from the
temperature logs to the serial port of the freezer. When this option is chosen, the
display reports how many temperature logs are in the system. While the data is
being sent out the serial port, it can be paused or completely cancelled through the
menu system.
Error Logs
SENS. ERR. LOGGING is accessible through the menu system of the control
(
MENU, 4, 2, 1). This menu choice turns on/off the logging of all sensor errors. The
choices are ENABLE or DISABLE. Records data in the error log.
LOW SUPPLY LOGGING is accessible through the menu system of the control
(
MENU, 4, 2, 2). This menu choice turns on/off the logging of the low LN
2
supply
error. The choices are ENABLE or DISABLE. Records data in the error log.
REMOTE ALARM LOGGING is accessible through the menu system of the control
(
MENU, 4, 2, 3). The menu choice turns on/off the logging of the remote alarm
activation. The choices are ENABLE OR DISABLE. Records data in the error log.
OPEN THERMOCOUPLE LOGGING is accessible through the menu system of
the control (
MENU, 4, 2, 4). This menu choice turns on/off the logging of the
thermocouple open alarm. The choices are ENABLE and DISABLE. Records data in
the error log.
HIGH TEMP #1 LOG is accessible through the menu system of the control
(
MENU, 4, 2, 5). This menu choice turns on/off the logging of the high temperature
alarm for Thermocouple #1. The choices are ENABLE and DISABLE. Records data in
the error log.
HIGH TEMP #2 LOG is accessible through the menu system of the control
(
MENU, 4, 2, 6). This menu choice turns on/off the logging of the high temperature
alarm for Thermocouple #2. The choices are ENABLE and DISABLE. Records data in
the error log.
18
KRYOS
Menu Access causes the control to make some decisions on logging an event and
they are handled in the following manner: Temperature is immediately logged (if it
is enabled) and then a fresh time period is started when the Menu system is exited.
System and error logs are placed in a suspended state until the control exits the
menu system and timing is started again. Duration of system and error logs then are
total time of the event less any time that the user was in the menu system.
When logs are dumped to the serial port, the oldest events are sent first. The control
operates on the FIFO (First In First Out) method. If the maximum number of entries
is reached, the oldest are lost to make way for the newest entries.
Dump Logs
DUMP SYSTEM LOGS is accessible through the menu system of the control
(
MENU, 4, 1, 1). This option sends data from the system logs out the serial port
of the freezer. When this option is chosen, the display reports how many system
logs are stored. While the data is being sent to the serial port, it can be paused or
completely cancelled through the menu system.
DUMP ERROR LOGS is accessible through the menu system of the control
(
MENU, 4, 1, 2). This option sends data from the error logs to the serial port of the
freezer. When this option is chosen, the display reports how many error logs are
in the system. While the data is being sent out the serial port, it can be paused or
completely cancelled through the menu system.
DUMP TEMP LOG #1 and TEMP LOG #2 are accessible through the menu system
of the control (
MENU, 4, 1, 3 or MENU, 4, 1, 4). This option sends data from the
temperature logs to the serial port of the freezer. When this option is chosen, the
display reports how many temperature logs are in the system. While the data is
being sent out the serial port, it can be paused or completely cancelled through the
menu system.
Error Logs
SENS. ERR. LOGGING is accessible through the menu system of the control
(
MENU, 4, 2, 1). This menu choice turns on/off the logging of all sensor errors. The
choices are ENABLE or DISABLE. Records data in the error log.
LOW SUPPLY LOGGING is accessible through the menu system of the control
(
MENU, 4, 2, 2). This menu choice turns on/off the logging of the low LN
2
supply
error. The choices are ENABLE or DISABLE. Records data in the error log.
REMOTE ALARM LOGGING is accessible through the menu system of the control
(
MENU, 4, 2, 3). The menu choice turns on/off the logging of the remote alarm
activation. The choices are ENABLE OR DISABLE. Records data in the error log.
OPEN THERMOCOUPLE LOGGING is accessible through the menu system of
the control (
MENU, 4, 2, 4). This menu choice turns on/off the logging of the
thermocouple open alarm. The choices are ENABLE and DISABLE. Records data in
the error log.
HIGH TEMP #1 LOG is accessible through the menu system of the control
(
MENU, 4, 2, 5). This menu choice turns on/off the logging of the high temperature
alarm for Thermocouple #1. The choices are ENABLE and DISABLE. Records data in
the error log.
HIGH TEMP #2 LOG is accessible through the menu system of the control
(
MENU, 4, 2, 6). This menu choice turns on/off the logging of the high temperature
alarm for Thermocouple #2. The choices are ENABLE and DISABLE. Records data in
the error log.
18
KRYOS
Menu Access causes the control to make some decisions on logging an event and
they are handled in the following manner: Temperature is immediately logged (if it
is enabled) and then a fresh time period is started when the Menu system is exited.
System and error logs are placed in a suspended state until the control exits the
menu system and timing is started again. Duration of system and error logs then are
total time of the event less any time that the user was in the menu system.
When logs are dumped to the serial port, the oldest events are sent first. The control
operates on the FIFO (First In First Out) method. If the maximum number of entries
is reached, the oldest are lost to make way for the newest entries.
Dump Logs
DUMP SYSTEM LOGS is accessible through the menu system of the control
(
MENU, 4, 1, 1). This option sends data from the system logs out the serial port
of the freezer. When this option is chosen, the display reports how many system
logs are stored. While the data is being sent to the serial port, it can be paused or
completely cancelled through the menu system.
DUMP ERROR LOGS is accessible through the menu system of the control
(
MENU, 4, 1, 2). This option sends data from the error logs to the serial port of the
freezer. When this option is chosen, the display reports how many error logs are
in the system. While the data is being sent out the serial port, it can be paused or
completely cancelled through the menu system.
DUMP TEMP LOG #1 and TEMP LOG #2 are accessible through the menu system
of the control (
MENU, 4, 1, 3 or MENU, 4, 1, 4). This option sends data from the
temperature logs to the serial port of the freezer. When this option is chosen, the
display reports how many temperature logs are in the system. While the data is
being sent out the serial port, it can be paused or completely cancelled through the
menu system.
Error Logs
SENS. ERR. LOGGING is accessible through the menu system of the control
(
MENU, 4, 2, 1). This menu choice turns on/off the logging of all sensor errors. The
choices are ENABLE or DISABLE. Records data in the error log.
LOW SUPPLY LOGGING is accessible through the menu system of the control
(
MENU, 4, 2, 2). This menu choice turns on/off the logging of the low LN
2
supply
error. The choices are ENABLE or DISABLE. Records data in the error log.
REMOTE ALARM LOGGING is accessible through the menu system of the control
(
MENU, 4, 2, 3). The menu choice turns on/off the logging of the remote alarm
activation. The choices are ENABLE OR DISABLE. Records data in the error log.
OPEN THERMOCOUPLE LOGGING is accessible through the menu system of
the control (
MENU, 4, 2, 4). This menu choice turns on/off the logging of the
thermocouple open alarm. The choices are ENABLE and DISABLE. Records data in
the error log.
HIGH TEMP #1 LOG is accessible through the menu system of the control
(
MENU, 4, 2, 5). This menu choice turns on/off the logging of the high temperature
alarm for Thermocouple #1. The choices are ENABLE and DISABLE. Records data in
the error log.
HIGH TEMP #2 LOG is accessible through the menu system of the control
(
MENU, 4, 2, 6). This menu choice turns on/off the logging of the high temperature
alarm for Thermocouple #2. The choices are ENABLE and DISABLE. Records data in
the error log.