Cypress CY7C1420AV18 - Manual (Page 20)

CY7C1416AV18, CY7C1427AV18
CY7C1418AV18, CY7C1420AV18
Document Number: 38-05616 Rev. *F Page 20 of 31
Maximum Ratings
Exceeding maximum ratings may impair the useful life of the
device. These user guidelines are not tested.
Storage Temperature ................................. –65°C to +150°C
Ambient Temperature with Power Applied.. –55°C to +125°C
Supply Voltage on V
DD
Relative to GND ........–0.5V to +2.9V
Supply Voltage on V
DDQ
Relative to GND.......–0.5V to +V
DD
DC Applied to Outputs in High-Z ......... –0.5V to V
DDQ
+ 0.3V
DC Input Voltage
[11]
.............................. –0.5V to V
DD
+ 0.3V
Current into Outputs (LOW) ........................................ 20 mA
Static Discharge Voltage (MIL-STD-883, M 3015).... >2001V
Latch up Current..................................................... >200 mA
Operating Range
Range
Ambient
Temperature (T
A
) V
DD
[15]
V
DDQ
[15]
Commercial 0°C to +70°C 1.8 ± 0.1V 1.4V to
V
DD Industrial –40°C to +85°C
Electrical Characteristics
DC Electrical Characteristics
Over the Operating Range
[12]
Parameter Description Test Conditions Min Typ Max Unit
V
DD
Power Supply Voltage 1.7 1.8 1.9 V
V
DDQ
IO Supply Voltage 1.4 1.5 V
DD
V
V
OH
Output HIGH Voltage Note 16 V
DDQ
/2 – 0.12 V
DDQ
/2 + 0.12 V
V
OL
Output LOW Voltage Note 17 V
DDQ
/2 – 0.12 V
DDQ
/2 + 0.12 V
V
OH(LOW)
Output HIGH Voltage I
OH
=
−0.1 mA, Nominal Impedance
V
DDQ
– 0.2 V
DDQ
V
V
OL(LOW)
Output LOW Voltage I
OL
= 0.1 mA, Nominal Impedance V
SS
0.2 V
V
IH
Input HIGH Voltage V
REF
+ 0.1 V
DDQ
+ 0.3 V
V
IL
Input LOW Voltage –0.3 V
REF
– 0.1 V
I
X
Input Leakage Current GND
≤ V
I
≤ V
DDQ
−5
5
μA
I
OZ
Output Leakage Current GND
≤ V
I
≤ V
DDQ,
Output Disabled
−5
5
μA
V
REF
Input Reference Voltage
[18]
Typical Value = 0.75V 0.68 0.75 0.95 V
I
DD
[19]
V
DD
Operating Supply V
DD
= Max,
I
OUT
= 0 mA,
f = f
MAX
= 1/t
CYC
300MHz (x8) 845 mA
(x9) 850
(x18) 900
(x36) 990
278MHz (x8) 795 mA
(x9) 800
(x18) 835
(x36) 910
250MHz (x8) 725 mA
(x9) 725
(x18) 760
(x36) 825
Notes
15. Power up: assumes a linear ramp from 0V to V
DD
(min) within 200 ms. During this time V
IH
< V
DD
and V
DDQ
< V
DD
.
16. Outputs are impedance controlled. I
OH
= –(V
DDQ
/2)/(RQ/5) for values of 175 Ω < RQ < 350Ω.
17. Outputs are impedance controlled. I
OL
= (V
DDQ
/2)/(RQ/5) for values of 175 Ω < RQ < 350Ω.
18. V
REF
(min) = 0.68V or 0.46V
DDQ
, whichever is larger, V
REF
(max) = 0.95V or 0.54V
DDQ
, whichever is smaller.
19. The operation current is calculated with 50% read cycle and 50% write cycle.
[+] Feedback