Cypress Perform CY7C1380F - Manual

CY7C1380D, CY7C1382D
CY7C1380F, CY7C1382F
18-Mbit (512K x 36/1M x 18)
Pipelined SRAM
Cypress Semiconductor Corporation • 198 Champion Court • San Jose
,
CA 95134-1709 • 408-943-2600
Document #: 38-05543 Rev. *F Revised January 12, 2009
Features
■ Supports bus operation up to 250 MHz
■ Available speed grades are 250, 200, and 167 MHz
■ Registered inputs and outputs for pipelined operation
■ 3.3V core power supply
■ 2.5V or 3.3V I/O power supply
■ Fast clock-to-output times
❐ 2.6 ns (for 250 MHz device)
■ Provides high performance 3-1-1-1 access rate
■ User selectable burst counter supporting Intel Pentium ® inter-
leaved or linear burst sequences
■ Separate processor and controller address strobes
■ Synchronous self-timed write
■ Asynchronous output enable
■ Single cycle chip deselect
■ CY7C1380D/CY7C1382D is available in JEDEC-standard
Pb-free 100-pin TQFP, Pb-free and non Pb-free 165-ball FBGA
package; CY7C1380F/CY7C1382F is available in
JEDEC-standard Pb-free 100-pin TQFP, Pb-free and non
Pb-free 119-ball BGA and 165-ball FBGA package
■ IEEE 1149.1 JTAG-Compatible Boundary Scan
■ ZZ sleep mode option
Functional Description
The CY7C1380D/CY7C1382D/CY7C1380F/CY7C1382F [1]
SRAM integrates 524,288 x 36 and 1,048,576 x 18 SRAM cells
with advanced synchronous peripheral circuitry and a two-bit
counter for internal burst operation. All synchronous inputs are
gated by registers controlled by a positive edge triggered clock
input (CLK). The synchronous inputs include all addresses, all
data inputs, address-pipelining chip enable (CE
1
),
depth-expansion chip enables (CE
2
and CE
3
[2] ), burst control
inputs (ADSC, ADSP, and ADV), write enables (BW
X
, and BWE),
and global write (GW). Asynchronous inputs include the output
enable (OE) and the ZZ pin.
Addresses and chip enables are registered at rising edge of
clock when address strobe processor (ADSP) or address strobe
controller (ADSC) are active. Subsequent burst addresses can
be internally generated as they are controlled by the advance pin
(ADV).
Address, data inputs, and write controls are registered on-chip
to initiate a self-timed write cycle.This part supports byte write
operations (see
Table 1 on page 6 and “Truth Table” on page 10
for further details). Write cycles can be one to two or four bytes
wide as controlled by the byte write control inputs. GW when
active LOW causes all bytes to be written.
The CY7C1380D/CY7C1382D/CY7C1380F/CY7C1382F
operates from a +3.3V core power supply while all outputs
operate with a +2.5 or +3.3V power supply. All inputs and outputs
are JEDEC-standard and JESD8-5-compatible.
Selection Guide
Description 250 MHz 200 MHz 167 MHz Unit
Maximum Access Time 2.6 3.0 3.4 ns
Maximum Operating Current 350 300 275 mA
Maximum CMOS Standby Current 70 70 70 mA
Notes
1. For best practices or recommendations, please refer to the Cypress application note AN1064, SRAM System Design Guidelines on www.cypress.com .
2. CE
3,
CE
2
are for TQFP and 165 FBGA packages only. 119 BGA is offered only in 1 chip enable.
[+] Feedback