Great Plains UT5052 Operator Manual - Manual (Page 2)

Great Plains Mfg., Inc. Table of Contents
2/18/2009 Series I UT3030-UT5052 Ultra-Till 576-026M
Table of Contents
Important Safety Information .......................... 1
Safety Rules................................................... 6
Safety Decals ................................................ 7
Introduction ........................................................ 12
Description of Unit ........................................ 12
Using this Manual ........................................ 12
Definitions.............................................. 12
Owner Assistance .......................................... 12
Assembly and Setup Assistance .................... 13
Product Support ..................................... 13
Pre-Assembly Checklist ........................ 13
Section 1 Assembly ............................................. 14
Center Frame, Torque Tube & Walking
Beam Assembly ....................................... 14
Inside Wing and Wheel Arm Assembly ....... 15
Brace Bar, Wing Brace & Rocker/Fold
Bracket Assembly .................................... 16
Outside Wing Assembly ............................... 17
Connecting Outside Wing and Wing Brace
Assembly ................................................. 18
Center Gang & Gang Hanger Assembly. ...... 19
Center Truss, Hitch and Strut Assembly ...... 20
Self Level and Rest Pads Assembly ............. 21
Fold Cylinders, Rocker Arm and 3” Rollers
Assembly ................................................. 22
Center Wing Stop and Outside Wing Stop
Assembly ................................................. 23
Front Gauge Wheel Assembly ..................... 24
Hydraulic Gauge Wheel Assembly .............. 25
Completing Setup ......................................... 26
Section 2 Hydraulics .......................................... 28
3030 Hydraulic Down Pressure
Preparation and Setup .............................. 28
5-Section Hydraulic Down Pressure
Preparation and Setup .............................. 29
Section 3 Layouts ............................................... 30
UT3030D Machine Layout, Disc.................. 30
UT5036D Machine Layout, Disc.................. 32
UT5042D Machine Layout, Disc.................. 34
UT5052D Machine Layout, Disc.................. 37
UT3030C Machine Layout, Coulter
(S/N A1095A-)......................................... 40
UT5036C Machine Layout, Coulter
(S/N A1095A-)......................................... 42
UT5042C Machine Layout, Coulter
(S/N A1095A-)......................................... 44
UT5052C Machine Layout, Coulter
(S/N A1095A-)......................................... 47
UT3030C Machine Layout, Coulter
(S/N A1096A+)........................................ 50
UT5036C Machine Layout, Coulter
(S/N A1096A+)........................................ 52
UT5042C Machine Layout, Coulter
(S/N A1096A+)........................................ 54
UT5052C Machine Layout, Coulter
(S/N A1096A+)........................................ 57
Disc Gang Identification .............................. 60
Coulter Gang Identification .......................... 62
Section 4 Operating and Maintenance.............. 64
Adjustments Before Going to the Field ....... 64
Field Adjustments & General
Operating Instructions .................................. 65
Maintenance and Lubrication ....................... 66
Section 5 Specification and Capacities ............. 67
Appendix ............................................................. 68
Torque Values for Common Bolt Sizes ....... 68
Tire Inflation Chart ...................................... 68
Warranty ....................................................... 69
© Copyright 2004 All rights Reserved
Great Plains Manufacturing, Inc. provides this publication “as is” without warranty of any kind, either expressed or implied. While every precaution has been taken in the
preparation of this manual, Great Plains Manufacturing, Inc. assumes no responsibility for errors or omissions. Neither is any liability assumed for damages resulting from
the use of the information contained herein. Great Plains Manufacturing, Inc. reserves the right to revise and improve its products as it sees fit. This publication describes
the state of this product at the time of its publication, and may not reflect the product in the future.
Great Plains Manufacturing, Incorporated Trademarks
The following are trademarks of Great Plains Mfg., Inc.: Application Systems, Ausherman, Land Pride, Great Plains
All other brands and product names are trademarks or registered trademarks of their respective holders.
Printed in the United States of America.