SARGENT 8200 Mortise Lock with BHL Trim - Manual

U.S. Patent Numbers: 5,678,870; 7,188,870 & 7,452,012
Standard 8200 Mortise Lock Sectional Trim Description & Part Number
Tools Required:
• Phillips screwdriver (standard size)
• 1/8" Allen wrench
• Phillips & flat tip screwdriver
How To Change Hand of Lock
How to Change Function of Lock:
Green catch screw must be located as designated on lock case to create desired function.
3 locations: One for 05, 37 & 38 functions
One for 04, 06, 13, 17 & 31 functions
And one for 36 function
Note: When moving green catch screw to 04, 06, 13, 17 & 31 functions, hub
position must be at 45° as shown on lockcase.
* Note: 17 function requires both levers to be rigid. Rotate red locking piece 90°,
so red surface of slide faces back of lockbody.
*See How to Change Hand of Lock, page 6.
36
05
37
38
04 06 13 17 31
CHECK HUB
HUB
Items needed to create each of the following functions:
#41 Cylinder is standard for both single & double cylinder functions for 1-3/4”
thick door
NOTE: Trim-one-side functions always require an inside trim assembly which can
be used on the inside or outside of the door (to order Trim one-side kit
(for all trim except PT or FE) order part # 82-4611.
03/F29
Classroom
dead lock
21/F17
Dead lock
30
Dummy trim
dead lock
56
Inner entry lock
89/F06
Hold back lock
90
Classroom
security hold back
lock
91
All purpose hold
back lock
92
All purpose hold
back lock
If shaded, knob or
lever rigid at all times
93
Dummy trim
94
Dummy trim
95
Single trim
dummy lock
96
Double trim
dummy lock
97
Active trim
dummy lock
65/F22
Privacy bedroom
or bath lock
66/F19
Privacy bedroom
or bath lock
67/F26
Institutional
privacy lock
68/F02
Privacy bedroom
or bath lock
70/71
Electrical
70: Fail safe
71: Fail secure
72/73
Electrical
72: Fail safe
73: Fail secure
76/77*
Electrical
entry lock
(* No cylinder on
77 function
78/79*
Electrical
entry lock
(* No cylinder on
79 function
45/F12
Dormitory or
exit lock
46/F11
Dormitory or
exit lock
47/F08/F10
Front door lock
or apartment
corridor lock
48/F35
Store door lock
49
Security deadbolt
50/51F15
Hotel guest
lock/Store room
deadbolt lock
52
Institution
deadbolt lock
55/F04
Office or
entry lock
31
Utility
lock
35
Storeroom
lock
36
Closet
lock
37/F05
Classroom
lock
38/F32
Classroom
security intruder
latchbolt lock
39/F33
Classroom
security intruder
deadbolt lock
40/41/F34
Classroom
security intruder
deadbolt lock
22/F16
Dead lock
23
Classroom
dead lock
24/F21
Room door
lock
25/F13
Dormitory or
exit lock
26/F14
Store door lock
27
Closet or
storeroom lock
28
Dummy trim
dead lock
29
Dummy trim
dead lock
04/F07
Storeroom
closet lock
05/F04
Office or
entry lock
06
Storeroom or
service lock
13/F31
Communicating
or exit lock
15/F01
Passage or closet
latch
16/F09
Apartment or exit
or public toilet
lock
17/F30
Asylum or
institutional lock
20/F18
Dead lock
43/F20
Apartment
corridor door lock
59
Double locking
I nstructions for Installing SARGENT
8200 Mortise Lock With BHL Trim
SARGENT 8200 Series Mortise Lock Function List 7800/8200 Mortise Locks
Multi-function Lockbody Options
04, 05, 06, 13, 17, 31, 36, 37, 38
INSIDE
INSIDE
OUTSIDE
OUTSIDE
LEFT HAND
LEFT HAND
REVERSE
BEVEL
RIGHT HAND
RIGHT HAND
REVERSE
BEVEL
DOOR HANDS DETERMINED FROM OUTSIDE
DOOR HANDING
Note: Beveled surface of latch must face
strike. The deadlatch is self adjusting. To
change hand of latch:
Note: Red surface of locking piece must face
secure side of door.
To rotate locking piece:
1. Position lockbody with red surface of locking
piece visible
2. Insert blade type screwdriver into locking
piece slot to rotate locking piece
3. Push locking piece toward back of lock body
and rotate 180° until RED surface shows on
opposite side
Red color indicates locked
side of door or hold back
side (91 and 92 Functions)
Locking
piece
slot
Lock front
Latch
1. Insert screwdriver
blade into the
spade shaped
slot
2. Rotate screwdriver 90º to push latch
out until back of latch clears lock front.
Then rotate latch 180º.
Latch will then re-enter lockbody.
(Note: Latch can not be unscrewed)
NOTE: 05 FUNCTION HAS A THUMB TURN ON THE INSIDE FACE
OF DOOR AND 55 FUNCTION HAS TOGGLE ON LOCK FRONT
A8131:C 1 6 5
Note: Shaded Levers are Rigid at all times
Function Outside
Lever
Inside
Lever
Trim One
Side Kit
Outside
Cylinder
Inside
Cylinder
Thumb
Turn
04 X X X
05 X X X X***
06 X X X
13 X X
17 X X X X
31 X X X
36 X X X
37 X X X
38 X X X X
Installation for levers and knobs is identical
Note: 04, 06, 13, 17 and 31 Functions require:
(a) Green catch screw to be removed
(b) Rotate hub to 45º position
(c) Rotate locking piece for required hand
(d) Red surface faces locked side of door
(e) Rotate hub to the original 45º
position as shown on lockcase
(f) Green catch screw is then reinstalled
Copyright © 2012,2014, Sargent Manufacturing Company, an ASSA ABLOY
Group company. All rights reserved. Reproduction in whole or in part without the
express written permission of Sargent Manufacturing Company is prohibited.
item part no. description req'd
1 82-1360 OUTSIDE LEVER HANDLE 1
2 01-1421 6-32 x 5/16" PH FL U-CUT MACHINE SCREW 2
3 92-0091 "LR" SECURITY ROSE 2
4 81-0723 MOUNTING POST 2
5 82-4663 O/S ADAPTER PLATE 1
6 82-0691 BUSHING(OUTSIDE) 1
7 82-0368 SPINDLE 1
8 82-4934 SPINDLE ADAPTER PACK 1
9 13-0140 SPRING 1
10 92-0013 TAPERED CYLINDER ROSETTE 1
11 01-1378 6-32 x 1/4" PH FL U-CUT HEAD MACHINE SCREW 3
12 82-3871 EMERGENCY BUTTON ASSEMBLY 1
13
01-4370 #6-32 x 3/8" PH RD HD MACHINE SCREW
2
01-1491 #6 x 3/8" LENGTH WOOD SCREW
14 92-0044 BACK PLATE (TURN KNOB) 1
15 82-0368 SPINDLE 1
16 92-2171 INSIDE ADAPTER PLATE 1
17 92-2604TAB LR TURN PIECE PACK 1
18 01-1495 MACHINE SCREW (SEMS) 2
22 01-1440 HANDLE SET SCREW 1
23 82-1359 INSIDE LEVER HANDLE 1
24 82-3184 LOCK BODY 1
25 82-0082TAB OUTSIDE FRONT STAMPED 1
27 01-1376 6-32 X 1/4" TORX U-CUT FL HEAD MACHINE SCREW 2
28 82-0614 SPINDLE ANCHOR 1
29 82-0347 SPINDLE SPRING 1
Scan to see a
video of this
installation step.
Scan to see a
video of this
installation step.