GBC Digicoil - Manual (Page 3)

3
FOR YOUR SAFETY
•
Do not connect the DigiCoil to electrical power or
attempt to operate it before you read this Operator
Manual and have been fully trained to operate it.
•
Save this Operator Manual for later use.
•
Keep hands, long hair, neckties, necklaces and
other loose articles away from moving parts.
•
Never override or attempt to defeat electrical or
mechanical interlock devices. Machine will not
operate normally when covers are removed.
•
Do not insert objects or spill liquids into the
DigiCoil. They may contact dangerous voltage or
short out components that may result in fire or
electric shock.
•
Only connect the DigiCoil to the electrical supply
shown in the machine specification section of the
Operator Manual and the serial/rating label located
on the equipment. Connect to a socket-outlet
installed near the product that is easily accessible.
•
Do not alter the plug on the end of the cord set (if
provided) of the DigiCoil. It was selected for your
safety.
•
Connect the plug only to a matching receptacle. If
you do not have such a receptacle, contact a
qualified electrician to have one installed.
•
Turn the DigiCoil power “Off” (O) at the end of the
day.
•
Unplug the DigiCoil before moving it or when it
will not in use for an extended period of time.
•
Do not attempt to service the DigiCoil. Contact an
authorized GBC service representative if any of the
conditions listed below are encountered:
•
Damaged plug or frayed power cord.
•
If liquid has been spilled into the product.
•
If the product has been exposed to rain or
water.
•
If the product has been dropped, bumped or
dented.
FCC NOTE: This equipment has been tested and
found to comply with the limits for a Class A digital
device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection
against harmful interference when the equipment is in a
commercial environment. This equipment generates,
uses, can radiate radio frequency energy and, if not
installed and used in accordance with the Operator
Manual, may cause harmful interference to radio
communications. Operation of this equipment in a
residential area is likely to cause harmful interference in
which case the user will be required to correct the
interference at his/her own expense.
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and (2)
this device must accept any interference received
including interference that may cause undesired
operation.
CAUTION: CHANGES OR MODIFICATIONS NOT
EXPRESSLY APPROVED BY GENERAL BINDING
CORPORATION COULD VOID YOUR
AUTHORITY TO OPERATE THE EQUIPMENT.
Department of Communications (CANADA)
Note: This Class A digital apparatus meets all
requirements of the Canadian Interference-Causing
Equipment Regulations.
Cet appareil numérique de la classe A respecte toutes les
exigences du Règlement sur le matériel brouiller du
Canada
MAIN CORDSET SELECTION (FOR 230VAC
MACHINE ONLY)
CAUTION: WHEN CHOOSING A
DETACHABLE LINE CORD FOR USE
WITH THE DIGICOIL, ALWAYS
OBSERVE THE FOLLOWING PRECAUTIONS:
The cordset consists of three components; the
attachment plug, cordage and appliance inlet. Each of
these must have European regulatory approvals for
safety.
The following minimum electrical ratings for the
specific cordset are published for safety purposes. DO
NOT USE CORDSETS THAT DO NOT MEET THE
FOLLOWING MINIMUM ELECTRICAL
REQUIREMENTS.
PLUG: 480 amperes, 250 volts, 50/60 Hz, Class 1, 3
conductor, European safety approved.
CORDAGE: Type HO3VV-F3G0.75, Harmonized
(+HAR+). The “++” symbols indicate cordage
approved to appropriate European standard (Note:
“HAR” may be substituted for approval mark of
European safety agency which approved the cordage.
An example would be “+VDE+”.
APPLIANCE CONNECTOR: 480A, 250 volts, 50/60
Hz, European safety approved. Type IEC 320. Cord-set
shall not exceed 3 meters in length. Cord-set with