Rockwell Automation 1102C-BOx93 Vacuum Contactor (200A) - Manual (Page 8)

42052-087
G. Ushakow
N/A
N/A
N/A
42052
1006490 1
INSTRUCTION SHEET
BULLETIN 1102C VACUUM CONTACTOR
CURRENT RATINGS 200A
200V-1500V
2-20-04
Mark Jutz 2-20-04
D. Josef 2-20-04
8 9
REVISION
AUTHORIZATION
DIMENSIONS APPLY BEFORE
SURFACE TREATMENT
H
A
B
C
D
E
F
G
(DIMENSIONS IN INCHES)
TOLERANCES UNLESS
OTHERWISE SPECIFIED
REFERENCE
SHEET OF DWG.
B
DR.
CHKD.
APPD.
DATE
DATE
DATE
±
±
±
ANGLES:
.XXX:
.XX:
THIS DRAWING IS THE PROPERTY OF
THE ALLEN-BRADLEY CO. INC.
AND MAY NOT BE COPIED, USED OR
DISCLOSED FOR ANY PURPOSE EXCEPT
AS AUTHORIZED IN WRITING BY
THE ALLEN-BRADLEY CO. INC.
LOCATION : MILWAUKEE, WISCONSIN U.S.A.
SIZE
1 2 3 4 5 6 7 8
E - DOC
42052-087-01(1)
Printed in U.S.A.
Replacement Parts
Accessories
Bulletin Number Voltage (input) Contactor Size (Amp. Rating)
1102C-BOD93 (200 Amp.)
1102C-BOA93 (200 Amp.)
1102C-BON93 (200 Amp.)
1102D-BOB93 (200 Amp.)
Bulletin Number Voltage (input) Control Pak Volts (Amp. Rating)
1102C-PK2D 108 VDC 110/120 VAC
1102C-PK2A 108 VDC 220/240 VAC
1102C-PK2N 108 VDC 380/415 VAC
1102C-PK2B 108 VDC 440/480 VAC
1102C-PK2G 125 VDC NONE
1102C-PK2H 250VDC NONE
Bulletin Number
1102C-VB2
Bulletin Number
1195C-N3
1195C-N4
Bulletin Number
1195C-LK1
Auxiliary Kits
Type - Contact Arrangement
Control Pak ---- side mounted module for DC coil power
110/120 VAC 1102C-CP2D
(200 Amp.)
(200 Amp.)
200 A Vaccum Interrupter Phase Assembly
Current Rating W/ Wire Gauge Range
Interrupter Phase Assembly Kit - Replacement for One Vacuum Interrupter Phase
Current Rating of Interrupter
(2) N.O. / N.C. 5 VDC 10mA
For use on DC input coils only - 125 VDC maximum
1195C-N5
(2) N.O. / N.C. 600 VAC 10 Amp. (A600)
200 A 2/0 - 250 MCM
Lug Kits
(1) N.O. / N.C. & (1) N.O. /Late Break N.C.
For use on DC input coils only - 250 VDC maximum
1195C-N6
(2) N.O. / Late Break N.C.
1102C-CP2A 220/240 VAC
380/415 VAC
1102C-CP2N
1102C-CP2B
440/480 VAC
Coil Kit ---- This kit contains the DC coil mounted in the sheet metal frame assembly
which attaches to the contactor mounting plate.
NOTE: When changing the coil voltage, verify that the Control-Pak voltage for the coil
kits listed below is in agreement with the Control-Pak nameplate input voltage.