Rockwell Automation 500LG Lighting Contactor (Mechanically and Electrically Held) - Manual (Page 4)

(4)
FUSE
2
FUSE
P1 P2 P3 P4 P5
C
A2 A1
C
C
ON
OFF
OFF ON R G
OFF ON R G
OFF ON R G
OFF ON R G
C C
2
P
N
P1 P2 P3 P4 P5
C
A2 A1
FUSE
2
FUSE C
C
(LEFT AUX.)
(RIGHT AUX.)
(LEFT AUX.)
(RIGHT AUX.)
C C
2
P
N
OFF ON
P1 P2 P3 P4 P5
ELECTRONIC MODULE
C
A1 A2
C
FUSE
2
FUSE
COIL
VOLTAGE
COIL
VOLTAGE
COIL
VOLTAGE
COIL
VOLTAGE
2
C C
P
N
OFF ON
P1 P2 P3 P4 P5
C
A1 A2
C
FUSE
2
FUSE
2
C C
P
N
OFF
HAND AUTO
TABLE D: OPTIONAL WIRING AND PILOT DEVICES FOR MECHANICALLY-HELD CONTACTOR, 3-WIRE CONTROL
TABLE B: OPTIONAL WIRING AND PILOT DEVICES FOR MECHANICALLY-HELD CONTACTOR, 2-WIRE CONTROL
OFF-ON OFF-AUTO SELECTOR SWITCH
HAND-OFF-AUTO ON-OFF-AUTO SELECTOR SWITCH
ON-OFF PUSHBUTTON
OFF-ON SELECTOR SWITCH
CONTROL VOLTAGE
CONTROL VOLTAGE
CONTROL VOLTAGE
CONTROL VOLTAGE
500LG(MECHANICALLY-HELD, 3-WIRE)
(OPTIONAL AUX.) (OPTIONAL AUX.)
500LG(MECHANICALLY-HELD, 2-WIRE)
C
ELECTRONIC
P2 P1
A1
P4 P3
MODULE
P5
A2
(OPTIONAL AUX.) (OPTIONAL AUX.)
CONTROL
VOLTAGE
N P
P N
TABLE A: 2-WIRE CONNECTION DIAGRAM
TABLE C: 3-WIRE CONNECTION DIAGRAM
(RIGHT AUX.)
(LEFT AUX.)
(RIGHT AUX.)
(LEFT AUX.)
(RIGHT AUX.)
(LEFT AUX.)
(RIGHT AUX.)
(LEFT AUX.)
NOT
USED
COIL
VOLTAGE
ELECTRONIC MODULE
ELECTRONIC MODULE
ELECTRONIC MODULE
3
C
ELECTRONIC
P2 P1
A1
P4 P3
MODULE
P5
A2
CONTROL
VOLTAGE
N
P
P N COIL
VOLTAGE
3
3
1
P
N
3
4 4
4 4
4 4
4 4
3
P
N
3
3
P
N
3
3
P
N
3
3
C
A1 A2
ON
R
OFF
G
ON
OFF FUSE FUSE
ON
C
OFF
L1 L2
2 2
C
A1 A2
ON
R
OFF
G
FUSE FUSE
C
L1 L2
2 2
C
A1 A2
ON
R
OFF
G
FUSE FUSE
C
L1 L2
2 2
OFF ON
OFF
HAND AUTO
TABLE F: OPTIONAL WIRING AND PILOT DEVICES FOR ELECTRICALLY-HELD CONTACTOR
OFF - ON OFF - AUTO SELECTOR SWITCH
HAND-OFF-AUTO ON-OFF-AUTO SELECTOR SWITCH
500LG(ELECTRICALLY-HELD)
C
A1 A2
(OPTIONAL AUX.) (OPTIONAL AUX.)
L1 L2
ON-OFF PUSHBUTTON
TABLE E: ELECTRICALLY-HELD
CONNECTION DIAGRAM
(RIGHT AUX.)
(RIGHT AUX.)
COIL
VOLTAGE
1
1
1
1
Wiring Diagram
Remote device 1
3
2 Additional control circuit overcurrent protection may be required when the control circuit conductors extend beyond the
enclosure. Refer to National Electrical Code.
Coil and control voltages may not be the same. check the voltage of the electronic module and coil before applying power.
4 For additional contact blocks for pilot lights or other signal indications, order two DSPT (500LG-142C) auxiliary contact blocks.
2-wire or 3-wire mechanically held lighting contactor comes standard with one SPST (500LG-141C) or two SPST (500LG-141C)
respectively.
LINE LOAD
1
2
3
4
5
6
1
2
3
4
5
6
TABLE G: CONTACT BLOCK POSITIONS
REFER TO TABLE A, C OR E FOR
CONTROL CONNECTION DIAGRAM
N.O. OR N.C.
N.O. ONLY
(RIGHT AUX.)
C