beautypg.com

Setting the clock, Auto clock setting, Manual clock setting – Toshiba DVR18 User Manual

Page 33

background image

33

EN

Int

rod
uct
ion

Co
nn
ect
ion
s

Basic Setup

Pl

ayback

Ed
iti

n

g

V

CR Fu

ncti

on
s

O

th

ers

Fu
nc
ti

on
Set

u

p

Recordi

n

g

Setting the Clock

Auto Clock Setting

This unit receives time signals from the analogue /
DVB channels, and sets the clock automatically. Set
the channel tuning before setting Auto Clock.

1

In stop mode, press [SETUP]. Select
“General Setting” using [

U / D],

then press [ENTER / OK].

2

Select “Clock” using [

U / D], then

press [ENTER / OK].

3

Select “Auto Clock Setting” using
[

U / D], then press [ENTER / OK].

• If any DVB channel has been set, the auto clock

is on. “Auto Clock Setting” will be displayed in
grey and you cannot select it.

4

Select “ON” using [

U / D], then

press [ENTER / OK].

The current time will be set automatically.

5

Press [SETUP] to exit.

6

Press [

ON / STANDBY] to turn

off.

The Auto clock function is activated.
• This unit will search for the time every time

when the power is turned off.

• Leave the unit off for several minutes to give it

time to set the clock.

Hint

• If you want to cancel “Auto Clock Setting”, select

“OFF” using [

U / D], and then press [ENTER / OK]

at the step 4.

Note

• The default setting of “Auto Clock Setting” is “ON”.
• The clock may set itself automatically after you

connect the antenna cable to the unit and plug in the
mains cable. In this case, the current time will
appear on the front panel display.

• If there are only analogue channels memorised in

this unit:
- The channel assigned to “904” must receive the

PDC signal in order to set the clock automatically.

- The unit will correct the current time by receiving

PDC broadcasts whenever the power is turned off.

- Between 23:00 and 1:00, the Auto Clock function

will not operate even when the power is turned off.

• The clock cannot be set automatically if you are not

receiving a channel in your area that carries a time
signal. In this case, set the clock manually.

• The unit will also correct the current time

automatically at 8:00 and 1:10 if the unit is in
standby mode or if you are watching DVB channel.

Manual Clock Setting

1

In stop mode, press [SETUP]. Select
“General Setting” using [

U / D],

then press [ENTER / OK].

2

Select “Clock” using [

U / D], then

press [ENTER / OK].

3

Select “Clock Setting” using [

U / D],

then press [ENTER / OK].

Default date will appear.

4

Press [ENTER / OK] again.

5

Enter the date (day / month / year)
using [

U / D].

Press [

P] to move the cursor to the next field. If

you want to go back to the previous field, press
[

L].

6

Enter the time (hours / minutes)
using [

U / D], then press

[ENTER / OK].

The clock will start.
• Although seconds are not displayed, they will be

counted from zero.

7

Press [SETUP] to exit.

Note

• Your clock setting will be lost if either there is a

power failure or the unit is unplugged for more than
30 seconds.

• If you have set the timer recording, “Clock” will be

displayed in grey and you cannot select it.

General Setting

Playback
Display
Video
Recording
Clock
Channel
DivX
HDMI
Reset All

Clock Setting

01 / 01 / 2008 ( TUE )

0 : 00

E9NG1BD_EN.book Page 33 Tuesday, April 8, 2008 6:21 PM