Pioneer VSX-D810S - Manual (Page 38)

38
En
Setting Up Using Preset Code
Search
An alternative method of setting up the remote with
preset codes is to use the search feature. The remote
transmits batches of 10 codes; when you see the
component responding you just scan through those last
10 codes until you find the correct one.
1 Switch on the component you want to
control.
If the component is some kind of player (CD player,
VCR, etc.), then start it playing.
2 Press and hold SETUP for three seconds.
The LED lights steadily for two seconds.
The remote control will also return to the previous
mode after thirty seconds of inactivity.
3 Press the MULTI CONTROL button for the
component you want to control.
Each button can be set to control one of the following
components
DVD DVD/LD player or DVR
TV TV, Satellite tuner or Cable TV tuner
VCR VCR or Digital Video Recorder
CD CD player
CD-R CD Recorder, Tape deck
or MD
TVC TV or Cable TV tuner
TUN FM/ AM tuner
4 Press and hold SETUP for two seconds.
A batch of 10 codes is transmitted and the LED
blinks during transmission. If you see the component
respond, by stopping (for playback components
only) or switching off, go on to the step 5, otherwise
repeat this step.
If you want to cancel the search mode, press and
hold
MUTING for three seconds (During LED blinks,
cann’t be cancelled).
Controlling the Rest of Your System
2,4
6,7
3
LED
4
TV
TVFUNC
MENU
VOLUME MASTER VOLUME
TV CONTROL
CHANNEL
ENTER
DISC
MPX
DISPLAY RF ATT
D.ACCESS
ST
TUNE
TUNE
ST
CLASS
ATT
BAND
/DTS DSP TEST TONE
CH SELECT CH LEVEL FUNCTION
SIGNAL SELECT
1 ¡ 4 ¢
7 8 3 ¶
EFFECT
DVD VCR CD-R TV
RCV TUN TVC CD
MIDNIGHT
LOUDNESS MUTING SETUP FL DIMMER
MULTI CONTROL
5.1 / 7.1
RECEIVER SOURCE
1 2 3
4 5 6
7 8
10
9
0
2
Learning Mode: Programming
Signals from other Remote
Controls
If preset codes are not available for your component(s),
or the available preset codes do not operate correctly,
you can use this function to program in signals from the
remote control(s) of your other component(s). This
operation can also be used after recalling a preset code
to program additional operations not covered in the
preset codes.
2
LED
3
TV
TVFUNC
MENU
VOLUME MASTER VOLUME
TV CONTROL
AV PRE-PROGRAMMED AND LEARNING
REMOTE CONTROL UNIT
CHANNEL
ENTER
DISC
MPX
DISPLAY RF ATT
D.ACCESS
ST
TUNE
TUNE
ST
CLASS
ATT
BAND
/DTS DSP TEST TONE
CH SELECT CH LEVEL FUNCTION
SIGNAL SELECT
1 ¡ 4 ¢
7 8 3 ¶
EFFECT
DVD VCR CD-R TV
RCV TUN TVC CD
MIDNIGHT
LOUDNESS MUTING SETUP FL DIMMER
MULTI CONTROL
5.1 / 7.1
RECEIVER SOURCE
1 2 3
4 5 6
7 8
10
9
0
2
1,6
5 Switch the component back on or restart
playback.
6 Use the
% fi buttons to scan through the last 10
codes transmitted to identify the correct code.
The LED will blink during transmission of the code.
Stop when you see the component stop or switch off.
You can also verify you have the correct code by
pressing PLAY, STOP, VOL +/–, etc.
7 Press and hold ENTER for three seconds to
save the preset code.
The remote control automatically returns to normal
usuage.
MEMO:
• After the remote control has transmitted all the codes
it will go back to the first code and start transmitting
them again automatically.
4
These buttons can
be programmed.